FAW Jiefang Automotive 485 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 57

background image

On the speed governor is also fitted a maximum fuel flow position-limit screw, which is

connected with speed-governing spring thrust-plate. This screw is used to limit maximum

fuel-supply flow-rate, and prevent the engine from overloading at each gear of speed. For the

maximum fuel flow position-limit screw, the adjustment work has already been done before

delivery, and should not be performed during operation.

On the casing of speed governor, a stoppage handle is fitted. When the engine needs to be

stopped, move this handle, then the engine will be stopped.

Above the cover of speed governor, is fitted a respirator part, below which there is a oil-drain

screw plug. As the speed governor seat is connected with oil pump body, when oil level appears in

oil indication window of fuel-injection pump, oil level in the speed governor can also meet

requirement for lubrication.

5. Fuel injector

Fuel injector is S series.

Fuel injector consists of injector body, nozzle cap, needle valve couple, push rod,

pressure-adjusting spring and pressure-adjusting screw etc. See Fig. 13.

The high-pressure fuel oil, pumped by fuel-injection pump, enters the chamber of fuel

injector needle valve couples, via high-pressure fuel pipe. Oil pressure acts on the conic surface of

needle valve. When fuel pressure overcomes the resistance of pressure-adjust spring, the needle

valve is raised, and fuel oil is injected via fuel-injecting hole into the combustion chamber.

Fuel injection nozzle's needle valve and needle valve body are couples, having been

pair-ground. During disassembling/assembling process, do not interchange them, and keep them

clean.

29

«
...
34
35
36
37
38
...
»

Содержание 485


























































Отзывы:

Нет отзывов

Похожие инструкции для 485

Бренд: Waldbeck Страницы: 72

Бренд: Ibiza Страницы: 3

Бренд: Aerotech Страницы: 59

Бренд: Polini Страницы: 32

Smart Motor SM23166MT

Бренд: MOOG ANIMATICS Страницы: 32

Бренд: Himax Страницы: 2

5.7L Corvette 2004

Бренд: Chevrolet Страницы: 1000

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 13

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды