Fasel Elektronik FCU2000 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 40

Fasel Elektronik FCU2000 Series Скачать руководство пользователя страница 11

Technical Data

Installation instructions Sauna control Series FCU2x00/FCU3x00/FCU4x00 / Version V 2.18

11

NOTE!

FASEL additionally offers a extension power unit for loads of 9 kW, 18
kW and 24 kW.

2.3

If the sauna control device is installed in the technical room

If the sauna
control device
is not directly
installed on the
outer wall of the
cabin

The control device can be installed directly on the outer side of the cabin or at another
location, however not within the cabin. If the installation is not done directly on the outer
wall of the cabin then the following points should be noted:

Lay the signal cables separately from the power line.

Do not lay the signal cables parallel to the power line.

Install a distribution box for the signal lines and another one for the power lines as per

Figure 1

Note EN 60335-2-53 for remote start

Figure 1: Cabling while installing the sauna control device not directly on the outer wall of the cabin

«
...
9
10
11
12
13
...
»

Содержание FCU2000 Series









































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды