Farr HD8625, Техническое руководство

Страница: 127 / 156

T
echnical
M
anual
hD8625 8-
5
/
8
” 35K T
ong
7.3
h
yDraulic
c
oMponenTs
Technical Information - All Styles
V
AN
E
CRO
SS
ING
V
AN
E
The Rineer patented vane crossing vane design produces
much higher volumetric and mechanical efficiencies than is
possible with a standard vane type design. This design
provides a sealing vane between cavities to improve
mechanical and volumetric efficiencies.
ST
AR
T
ING AND
ST
A
LL T
OR
Q
U
E
The Rineer motor produces torque curves which are virtually
flat, with starting and stall torque equal to approximately 90-
94% of theoretical torque.
M
OR
E P
OW
E
R
ST
RO
KES PE
R R
EV
O
L
U
T
ION
The 15 Series has four stator cavities and 10 rotor vanes.
E
ach rotor vane works in each stator cavity once per
revolution, which results in 40 power strokes per revolution.
This helps produce higher mechanical efficiency and flatter
torque curves.
BE
ARING
L
OADING
The bearings in the 15 Series can accept radial load per the
radial capacity chart. Thrust load is not recommended under
most conditions. Consult with a Rineer Application
E
ngineer
for optional bearing configurations to match your application.
SE
A
LS
B
una N seals are supplied as standard on the Rineer 15
series motors. Viton seals may be ordered as an option.
RO
T
A
T
ING GROU
P - 1S or 1H
Under most operating conditions, 1S (standard rotating
group parts) should be used. Under some high speed
conditons 1H can be specified.
RO
T
A
T
ION
The 15 Series Motor rotates equally well in either direction
and smoothly throughout its entire pressure and speed
range.
L
ooking into the end of the shaft, rotation is clockwise
when oil is supplied to port "A".
H
OR
SEP
OW
E
R
L
I
M
I
T
A
T
ION
Maximum horsepower limitations may vary with different
applications.
When using the 15 Series
Motor above 75
HP, consult a Rineer Application Engineer.
F
I
LT
RA
T
ION
25 micron minimum.
FL
UID
We suggest premium grade fluids containing high quality rust,
oxidation and foam inhibitors, along with anti-wear additives.
For best performance, minimum viscosity should be
maintained at 100 SSU or higher. Fluid temperature should not
exceed 180
O
F.
E
levated fluid temperature will adversely affect
seal life while accelerating oxidation and fluid breakdown. Fire
resistant fluids may be used with certain limitations. Contact
Rineer for additional information.
CA
SE
DRAIN
The 15 Series Motor is designed for either internal or external
case drain. Two case drain ports are supplied. When using
internal case drain, simply plug the two ports. When using
external case drain, use the port at the highest elevation. We
recommend case drain pressure of 35 PSI or less when using
the standard seals.
CA
SE
DRAIN CIRCU
L
A
T
ION
Fluid should be circulated through the case when a
temperature differential exists between the motor and the
system in excess of 50
O
F. Should this occur, contact a
Rineer Application Engineer.
M
OUN
T
ING
The mounting position is unrestricted. The shafts, pilots, and
mounting faces should be within .002 TIR.
IN
TE
R
M
I
TTE
N
T
CONDI
T
ION
S
Intermittent conditions are to be less than 10% of every minute.
O
THE
R A
V
AI
L
A
BLE M
O
T
OR
S
For information on additional Rineer Motors, request one of the
following publications:
37 Series ..............................................Publication DS371003
57 Series ..............................................Publication DS571003
125 Series ............................................Publication DS1251003
Technical Information - Retractable Shaft Motor
R
ET
RAC
T
ING
THE SH
A
FT
The shaft is spring loaded into the engaged position. Pulling
on the knob attached to the shaft at the rear of the motor will
move the shaft 1.25 inches into the motor.
CAU
T
ION
:
R
etracting the shaft must be done when the
motor and driven mechanism are not in o
p
eration and
are unloaded.
R
ET
AINING
SH
A
FT
IN R
ET
RAC
TE
D
P
O
S
I
T
ION
The shaft is retained in the retracted position by inserting a
2.0 inch wide spacer between the rear housing and the knob
attached to the shaft. Depending on the application and
mounting position of the motor, the spacer design may vary.
Spacers are not supplied with the motor.
R
E-E
NGAGING
THE SH
A
FT
This is accomplished by releasing the shaft, then rotating it
clockwise until the splines of the shaft line up and engage the
splines of the driven mechanism.
CAU
T
ION
:
R
e-engaging the shaft must be done when the
motor and driven mechanism are not in o
p
eration and are
unloaded.
BE
ARING
L
OADING
The 15 series Retractable is not suitable for applications which
require radial or axial loading of the shaft.
M
OUN
T
ING
The mounting position is unrestricted.
CAU
T
ION
: The shaft
extension and knob at the rear of the motor rotates when
the motor is in o
p
eration.