Farr HD8625 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 156

background image

T

echnical

M

anual

hD8625 8-

5

/

8

” 35K T

ong

2.15

IMPROPERLY SECURED HYDRAULIC CONNECTIONS WILL INTERRUPT HYDRAULIC FLUID FLOW, AND
COULD RESULT IN THE FOLLOWING FAILURES:

• A restriction in the pressure supply hose will result in high pressure within the power unit hydraulic system, which

will activate the hydraulic governor and increase the engine speed to as high as maximum RPM.

• A restriction in the return line will result in high pressure within the power unit and the tong hydraulic system, caus-

ing engine speeds as high as maximum RPM, and possible failure of the motor seal.

Following inspection of the hoses, start the engine and allow it to idle until warm. Allow hydraulic fluid to circulate for approximately 10

minutes, then slowly close the Bypass Valve to allow hydraulic fluid to circulate through the hoses and to the tong (circulating pres-

sure should not exceed 200 psi). Place the tong gear shifter in low gear and rotate the tong slowly forward and then reverse with the

throttle valve control lever. Once this has been done and the proper size jaws have been installed, the tong is then ready to run pipe.

2.

Valve Operation

4-way proportional valves control operation of hydraulic devices on the tong assembly such as hydraulic motors and cylinders. When

any one valve is “centered” or in the detent position, there is no hydraulic output from the valve. When the valve is pushed forward

there is an effect, and when the valve is pulled back, there is an opposite effect. These valves feature proportional control, which

means that further extension of the valve handle (thereby further opening the valve orifice) results in proportionally higher hydraulic

output to the controlled device.
The following illustration demonstrates the type and effect of the hydraulic valves with which this tong is may be equipped.
TONG MOTOR
This is a proportional valve. Pushing the valve handle forward will cause the tong motor to rotate in a clockwise direction (as seen

from the top of the tong). This is the desired direction of rotation for making up a joint. Pulling the valve handle in the opposite direc-

tion results in counter-clockwise rotation, which is the desired direction of rotation for breaking out a joint.

I

llustratIon

2.g.1: t

ong

r

otatIon

C

ontrol

v

alve

Ensure adequate lube oil and hydraulic oil levels before starting engine. Use start up procedures as recommended by the power unit

engine operator’s manual. Open the Bypass Valve on the hydraulic system, and inspect all pressure and return line hose connections

to ensure correct and secure installation.

s

eTup

& o

peraTion

«
...
29
30
31
32
33
...
»

Содержание HD8625





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для HD8625

Бренд: Lambda Страницы: 25

Бренд: Gallagher Страницы: 96

Бренд: Navitar Страницы: 6

Бренд: Magnaflux Страницы: 6

Бренд: Earlex Страницы: 4

Бренд: Lamello Страницы: 156

Бренд: HOZAN Страницы: 2

Бренд: Rockwell Automation Страницы: 4

Бренд: MaxPro PROFESSIONAL Страницы: 50

Бренд: Whyte Страницы: 12

Бренд: Senco Страницы: 32

Бренд: Agilent Technologies Страницы: 142

Бренд: Campbell Hausfeld Страницы: 16

Бренд: OMERA Страницы: 50

Бренд: Parkside Страницы: 67

Бренд: B&B Страницы: 3

Бренд: RASOR Страницы: 15

Бренд: jbc Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды