Farr HD8625 Скачать руководство пользователя страница 136

Страница: 136 / 156

7.12

hD8625 8-

” 35K T

ong

echnical

anual

yDraulic

oMponenTs

WARNING:

RINEER RECOMMENDS FOLLOWING

ALL

STANDARD SHOP SAFETY PRACTICES SPECIFICALLY INCLUDING WEARING OF EYE PROTECTION.

1) Remove the rotor.

2) Remove both the rotor

and stator vanes.

3) Note: On motors

manufactured prior to

1987, rotor vane slots and

rotor vanes should be

numbered so that vanes

can be reassembled in the

same vane slot.

Inspect all springs and

seals. We recommend

replacement of all seals

and springs whenever the

motor has been

disassembled.

Inspect all parts and

replace any parts which

obviously show excessive

wear or damage.

VANES:

Normal wear results

in slight flattening of vane tips

which does not impair motor

performance. Replace vane if

radius is reduced by 50%.

Clearance between the rotor

vane and rotor vane slot

varies with the vane

selection. The design allows

the vane to "lean" slightly in

the slot, providing the

required mechanical seal.

Note: Measure the rotor

and stator length to the

fourth decimal point and

supply measurement when

ordering rotor, stator, or

vanes.

STATOR:

Normal wear results

in polishing of cam form which

does not impair motor

performances.

Noticeable wear may be

apparent along the corner of

one side of the staor vane

slot. This does not necessarily

require replacement of the

stator, but may slightly affect

volumetric efficiency.

ROTOR:

Normal wear

results in polishing of rotor

faces which does not impair

motor performance.

Examine the rotor vane

slots closely. Polishing

down in the slots is normal,

but if there is any indication

of a "pocket" forming in the

wall of the slot, the rotor

should be replaced.

PLATES:

Normal wear

results in marking of timing

plates which does not

impair motor performance.

Replacement of the timing

plate is required if any

smearing, galling, or heat

cracks are present.

INSPECTION AND REPLACEMENT

OF PARTS

Содержание HD8625





























































































































































Результаты поиска

Содержание HD8625

Отзывы:

Похожие инструкции для HD8625

Бренды по названию

Популярные бренды

Farr HD8625, Техническое руководство

Результаты поиска

Содержание HD8625

Отзывы:

Похожие инструкции для HD8625

Бренды по названию

Популярные бренды