FarmTek Growers Supply HydroCycle 11291950 страница 16 Скачать руководство пользователя

Страница: 16 / 41

11291950

Revision date: 09.20.21

DRILL TUBE HOLES IN LIDS AND INSTALL LIDS

Channel Preparation: Lids

Complete these steps to drill holes for the nutrient tubes:
1. Take twelve (12) channel lids and arrange so all the plant holes and ends of the lids align. Take the

remaining channel lids and repeat this step. Keep the two piles separate.

ATTENTION:

For the first pile of lids, drill the nutrient tube holes where the first plant hole is closest to the

end of the lid. See A in the photo.

For the remaining lids, drill the nutrient tube holes where the first plant hole is farthest from the end of the lid.

See B in the photo.

2. Once the lids are separated, move to pile A and drill one (1) 5/16" hole in each lid where plant hole is closest

to the end. See the diagram that follows. Keep lids in the same group when completed.

Hole

Centered

Lids are designed with off-set holes for improved plant growth. During installation, alternate lids as

shown. Before snapping lids onto the channels, drill the nutrient tube holes at one end of each lid.

Photo shows lids installed

so plant holes are offset.

Nutrient Tube

Holes

ATTENTION:

When sliding the lids onto the

channels, position the nutrient holes opposite

the drain end/elbow of the channel.

ATTENTION:

Drill holes away from open

channels to prevent debris from dropping

into the channels.

3. Move to pile B and drill one (1) 5/16" hole in each lid where plant hole is farthest from the end. See the

diagram that follows. Keep lids in the same group when completed.

Hole

centered.

1/2" to 3/4"

from end.

Hole

Centered.

1/2" to 3/4"

from end.

Содержание Growers Supply HydroCycle 11291950










































Результаты поиска

Содержание Growers Supply HydroCycle 11291950

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 11291950

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle 11291950, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle 11291950

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 11291950

Бренды по названию

Популярные бренды