FarmTek Growers Supply HydroCycle 11291950 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 41

background image

20

20

11291950

Revision date: 09.20.21

6

Assemble and Install Nutrient Supply Manifolds

7. Choose one manifold and place it on a flat surface with the marks facing up. Upper manifold is shown below.

8. Using a

3/8" drill bit

— a step bit is highly recommended — drill holes in PVC tube for top hat grommets at each of the

marks. Repeat this step to drill the remaining supply manifolds.

9. Next, disassemble each manifold and clean the pvc pipe to remove debris from inside the tube.

Keep parts for each

manifold together.

10. Insert one 115820 top hat grommet into each 3/8" hole in the PVC tube. Dip grommet in water for easier installation. Wipe off

chalk line if desired. Verify through holes in grommets. Puncture if necessary.

ASSEMBLE AND INSTALL NUTRIENT SUPPLY MANIFOLDS—CONTINUED

ATTENTION:

Grommet fit should be snug. If grommet seems loose or slides into hole with little effort,

verify you have drilled holes using a 3/8" bit.

Grommets will leak if hole diameter is too large.

11. Apply pvc primer and pvc cement to each end of one manifold pipe and reassemble the manifold using the fittings for that pipe.

Use the marks to position the fittings as they were before manifold was disassembled. Set the assembly aside and repeat the

step to reassemble all manifolds. Allow cement to set before continuing with next step.

WF6990

PVC Cement and

113372 PVC Primer

Alignment

Marks

Primer and Cement

Primer and Cement

ATTENTION:

If using a

twist drill bit (as shown),

apply slight pressure to

allow bit to cut a smooth

hole in PVC tube.

Step Bit

Grommet to be tight to PVC tube.

115820

Grommet

IMPORTANT:

Verify

there is an open hole

through the grommet

before installing.

Puncture through if

necessary.

«
...
18
19
20
21
22
...
»

Содержание Growers Supply HydroCycle 11291950










































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 11291950

Бренд: ABB Страницы: 86

Бренд: Parker Research Corp Страницы: 4

Бренд: Daihan Scientific Страницы: 43

Бренд: Nitecore Страницы: 4

Бренд: Velp Scientifica Страницы: 12

Бренд: J&M Страницы: 33

Бренд: Keithley Страницы: 79

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Additel Страницы: 139

Бренд: Vaisala Страницы: 2

Бренд: Xtricity Страницы: 4

Бренд: E-FLOR Страницы: 124

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

home FLP 1600 SOLAR

Бренд: Somogyi Elektronic Страницы: 15

TEMSTM POCKET 7.3

Бренд: ASCOM Страницы: 8

Бренд: Denon Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды