FarmTek Growers Supply HydroCycle 11291950 страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 41

background image

25

Revision date: 09.20.21

11291950

9

INSTALL THE MAIN PUMP & PLUMBING

Install the Main Pump and Plumbing

Gather parts identified in the photo and construct main pump supply plumbing. Review assembly and installation

notes that follow before you begin. For best results, complete this procedure after setting frame slope.

•  Dry fit all connections before applying pvc primer and pvc cement.
•  Install the WF1023 Y-filter with the water-flow direction arrow pointing away from the pump.
•  Center reservoir so bulkhead fitting points toward the supply manifold end of the frame.

WF1530

From Pump

WF1530

WF2160

WF3310

WF3410

WF1530

WF1023

WF2153

3/4" PVC

3/4" PVC

WF1320 tee

fitting at the

end of the

pvc manifold.

Water Flow

A

WARNING:

All electrical

wiring to be completed

by a qualified electrician

according to recognized

local building codes.

WF1530

water flow

Supply

Manifold

End

1/4"

Nutrient

Tube

1" PVC

3/4" PVC

Drain

Manifold

End

2" Drain

PVC

Reservoir

113536

Pump

113537

Unions

A

Side View of System

Drain

Drain

Bulkhead Fitting &

WF2193 Adapter

NOTE:

Secure

pump to mounting

surface to reduce

vibration.

See A in diagram above.

See A in diagram below.

«
...
23
24
25
26
27
...
»

Содержание Growers Supply HydroCycle 11291950










































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 11291950

Бренд: Makita Страницы: 84

Бренд: Salford Страницы: 64

Бренд: Vaisala Страницы: 60

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: Goobay Страницы: 6

ABS-Lock III-BE

Бренд: ABS Страницы: 8

Бренд: Phenix Technologies Страницы: 39

Chandler Engineering 1910

Бренд: Ametek Страницы: 46

Бренд: ORORO Страницы: 16

Бренд: PHAROS MARINE Страницы: 17

Бренд: Scilogex Страницы: 21

LED Niova 150-F Pro 150W Bi Color

Бренд: Walimex Pro Страницы: 56

Бренд: T&R Страницы: 26

The Huntington Raised Planter Bed

Бренд: Eden Страницы: 2

Бренд: Lightolier Страницы: 2

Бренд: Mgl Страницы: 2

Бренд: Claas Страницы: 252

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды