FarmTek Growers supply GrowSpan Gothic Pro 113836DD Скачать руководство пользователя | Manualshive

Страница: 26 / 61

background image

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

26

113836_37_38_39DD Revision date: 06.06.18

SET HEIGHT OF DROP-DOWN SIDE PANEL

The desired height for drop-down side panel is determined and marked

before

installing polycarbonate roof panels.

ATTENTION:

Consult Main Cover Details diagram in the Quick Start section of this manual to verify height of drop-down

panel.

Required distance from finished grade to bottom of roof panels is 42".

1. Measure and mark the height of drop-down side panel at 42" on the end rafter at one end of the greenhouse.

2.  Move to opposite end of the greenhouse (same side) and mark same height from finished grade on that end rafter.
3.  Stretch a chalk line along the side between the two points. Use a line level to ensure marks are level.
4.  Snap to mark bottom edge of polycarbonate roof panels.
5.  Continue by installing roof panels.

42"

Customer-Supplied Baseboard

Ground Level

«
...
24
25
26
27
28
...
»

Содержание Growers supply GrowSpan Gothic Pro 113836DD






























































Отзывы:

Нет отзывов

Похожие инструкции для Growers supply GrowSpan Gothic Pro 113836DD

Бренд: Halls Страницы: 36

Бренд: ACD Страницы: 66

Бренд: Palram Страницы: 84

Pro Solar Star R030

Бренд: ClearSpan Страницы: 69

Бренд: ACF Greenhouses Страницы: 34

Бренд: Halls Страницы: 52

Бренд: Palram Страницы: 30

Бренд: Dancover Страницы: 34

Бренд: LAMS Страницы: 32

Бренд: ACD PRESTIGE Страницы: 43

Бренд: LAMS Страницы: 80

Бренд: Gazebo penguin Страницы: 14

$Poly-Tex Superior EZ5006 Assembly Instructions Manual preview$

Superior EZ5006

Бренд: Poly-Tex Страницы: 22

$Poly-Tex Garden Mart Assembly Instructions Manual preview$

Бренд: Poly-Tex Страницы: 25

$Poly-Tex FieldPro Gothic High Tunnel 30 Installation Instructions Manual preview$

FieldPro Gothic High Tunnel 30

Бренд: Poly-Tex Страницы: 39

Бренд: Juliana Страницы: 29

Silverline 106 Lean-To

Бренд: Eden Halls Greenhouses Страницы: 25

Бренд: Eden Halls Greenhouses Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды