FarmTek Growers supply GrowSpan Gothic Pro 113836DD страница 33 Скачать руководство пользователя

Страница: 33 / 61

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.06.18 113836_37_38_39DD

INSTALL OVERLAP BRACING AND U-CHANNEL

View from

outside.

Upper Panel

Lower Panel

Install 8' aluminum

profile here along edge

of upper panel.

Upper

Panel

Aluminum profile attached

to bottom of upper panel

(outside of frame).

Lower Panel

Foil tape at top of lower panel.

Complete this procedure to finish panel installation:
1. Install 8' sections of aluminum profile (104213) along

lower edge of all upper panels on both sides. Trim last

section to length as needed.

NOTE:

Install long side of

profile on top of panel.

Do not use Tek screws or

washers when installing

aluminum U-channel at this

time.

104213 U-Channel

Long Side

of Profile

2. Move inside the frame and measure between rafters at

point where upper and lower panels overlap.

3. Cut a piece of 104779 (1.5" x 1.5") square tubing to fit

between rafters. (All tubes should be same length.)

NOTE:

Diagram (above) shows where to measure to

determine length of 1.5" x 1.5" tube. Diagram shows

installed panels as seen standing inside greenhouse.

4. From inside the frame, align square tube as shown

over lower end of upper panel (dashed line). Hold tube

in place tight against panel.

1.5" x1.5" Tube

(104779)

View from inside the shelter.

Foil tape at top of lower panel.

ATTENTION:

Align and install tube as shown to secure

upper and lower panels together at overlap seam.

View shows underside of panels as seen from inside

greenhouse.

IMPORTANT

Under no circumstances should a

support structure allow force or weight to be applied to

polycarbonate panels! Supports must span from rafter

to rafter when used. Consult a contractor if needed for

additional information. Take additional steps to protect

polycarbonate panel surface.

Use of a lift is strongly

recommended.

If bracing and U-channel trim were installed during

panel installation, skip this section and continue with the

installation of baseboards.

Foil Tape

(top of lower

panel inside)

Lower

Panel

1.5" x 1.5" (104779)

Backer Tube

(inside greenhouse)

U-Channel (bottom of

upper panel – outside)

Upper

Panel

Install 104213

U-channel here.

Dashed line shows

top of all lower panels

(inside greenhouse).

Содержание Growers supply GrowSpan Gothic Pro 113836DD






























































Результаты поиска

Содержание Growers supply GrowSpan Gothic Pro 113836DD

Отзывы:

Похожие инструкции для Growers supply GrowSpan Gothic Pro 113836DD

Бренды по названию

Популярные бренды

FarmTek Growers supply GrowSpan Gothic Pro 113836DD, Руководство по установке

Результаты поиска

Содержание Growers supply GrowSpan Gothic Pro 113836DD

Отзывы:

Похожие инструкции для Growers supply GrowSpan Gothic Pro 113836DD

Бренды по названию

Популярные бренды