Farm King 1370 Скачать руководство пользователя страница 57

Страница: 57 / 146

Maintenance - 1370, 1385, 1395, 13114 Backsaver Auger

ELECTRIC HOPPER CONTROL BOX
TROUBLESHOOTING

Applies to all Units Equipped With Control Box
SZ000997.

IMPORTANT

Check that wires and connectors are properly
installed.

Check wires for damage.

Unplug system when not in use.

Hopper Will Not Move Left Or Right

Check that the circuit breaker (Item 1) is not
deactivated. Push the button in to reset. This could
be caused by defective motors or pinched wiring

[Figure 50]

Check wiring for damage. Repair or replace
damaged wiring.

Check that all motors are operating properly.
Replace non-operational motor.

Hopper Will Only Move In One Direction

Disconnect the control box from the motors. Use
a volts ohm meter to check the voltage at the drive
wheel output wires.

There should be system voltage when pressing
the left / right button on the control box. If there
is voltage in both directions, the motor may be at
fault and will need to be replaced.

If there is voltage in only one direction but not in
the other, this is most likely a control relay failure
(Item 2)

[Figure 50]

Use the wire colors to determine the relay at fault:

• Green wire leads to the move-right relay

• White wire leads to the move-left relay

Replace defective relay.

Remote Control Functions Correctly But The
Move-Left/Right Switches On The Box Do Not

Check the wires leading to the move-left and
move-right switches (Item 3). Make sure the wires
are connected properly

[Figure 50]

Check wiring for damage. Repair or replace
damaged wiring.

Figure 50

Circuit breaker (Item 1) is

located behind the red splice

with heat shrink tubing.

Содержание 1370



















































































































































Результаты поиска

Содержание 1370

Отзывы:

Farm King 1370, Руководство оператора и каталог запасных частей, Страница: 57 / 146

Результаты поиска

Содержание 1370

Отзывы: