MODELLO FSV 32IT
DISPOSIZIONE DEI COMANDI
1- Interruttore generale
2- Pulsante di comando elettropompa del vuoto
3- Indicatore di vuoto
4- Pulsante luminoso per il comando della saldatura
5- Manopola per la regolazione del tempo di saldatura
1
2
3
4
5
MODEL FSV 32IT
LOCATION OF THE CONTROLS
1 - switch
2 - Push button electric vacuum
3 - Indicator empty
4 - Illuminated pushbutton for control of welding
5 - Knob for adjusting the welding time
ISTRUZIONI PER L'USO
1- Posizionare il timer di saldatura
5
sul valore "4";
2- Inserire il prodotto nel sacchetto di misura adeguata;
3- Sollevare il coperchio mobile, posizionare la bocca
del sacchetto 1 cm oltre la guarnizione nera,
abbassare il coperchio;
4- Premere il pulsante pompa
2
esercitando una
leggera pressione sul coperchio finchè l'indicatore
di vuoto non raggiungerà il valore "0.2".
5- A vuoto effettuato, dopo che la lancetta
dell'indicatore del vuoto si sarà stabilizzata, premere
il pulsante di saldatura
4
.
6- Attendere lo spegnimento automatico della pompa
vuoto.
SUGGERIMENTI
Il sacchetto deve essere proporzionato al prodotto.
Il timer di saldatura
5
va regolato in base allo spessore
del sacchetto: aumentando lo spessore del sacchetto
si dovrà aumentare il tempo di saldatura, diminuendo
lo spessore del sacchetto si dovrà diminuire il tempo
di saldatura. L'aspirazione può risultare più o meno
veloce in base alle proporzioni tra prodotto e sacchetto
e tra spessore e sacchetto. Con alcuni tipi di carne
può succedere di aspirare del sangue, questo non
andrà nella pompa ma si fermerà all'interno della
guarnizione che andrà subito pulita. Nel caso vi fosse
aspirazione di liquido rifare un'altra saldaura al di
sotto della precedente. Qualora si formassero grinze
lungo la saldatura ripeterla come spiegato sopra.
Prima di saldare dilatare il sacchetto con le mani per
eliminare eventuali sacche d'aria. Fare attenzione
alla carne con osso in quanto potrebbe forare il
sacchetto.
INSTRUCTIONS FOR USE
1- Place the welding timer
5
to the value "4";
2- Plug the product into the bag properly fitted;
3- Raise the movable lid, place the mouth of the bag
1 cm beyond the black gasket, lower lid;
4- Press the Pump
2
exerting a slight pressure on
the lid until the vacuum indicator will not reach the
value "0.2".
5- Empty carried out, after which the needle of the
vacuum has stabilized, press the welding
4
.
6- Wait for the automatic turning off the vacuum pump.
ADVICE
The bag must be proportional to the product. The
timer welding
5
should be adjusted according to the
thickness of the bag: increasing the thickness of the
bag you will have to increase the welding time,
decreasing the thickness of the bag you will have to
reduce the welding time. The aspiration may be more
or less fast to the proportions between the product
and the bag and between thickness and bag. With
some types of meat can happen to aspirate blood,
this will not go into the pump but will stop inside the
gasket that will immediately clean. In case there was
liquid suction redo another saldaura below the
previous. If wrinkles were formed along the seam to
repeat as explained above. Before welding dilate the
bag with your hands to remove any air pockets.
Pay attention to the meat on the bone as it may
puncture the bag.
Содержание FSV 32D
Страница 12: ......