MODELLO FSV 32S
FUNZIONI DEL DISPLAY
1- Interruttore per avviamento e stop vuoto
2- Led che segnala vuoto in corso
3- Pulsante per il comando della saldatura
4- Led di saldatura attiva
COMPONENTI
A- Carrozzeria
B- Display
C- Coperchio
D- Barra saldante teflonata
E- Guarnizione
F- Ugello per vuoto in contenitori
VUOTO IN SACCHETTI
1- Collegare la spina alla presa di corrente, dopo 5
secondi la macchina sarà attiva.
2- Alzare il coperchio mobile
C
posto nella parte
anteriore della macchina.
3- Posizionare il sacchetto fra le due guarnizioni
inferiori
E
facendo attenzione che il bordo non
presenti increspature e sia ben appoggiato al piano.
4- Abbassare il coperchio
C
esercitando una leggera
pressione sulle estremità laterali.
5- Premere il pulsante
1
: la macchina inizia ad aspirare
l'aria all'interno del sacchetto e si accende il primo
led dal basso
2
;
6- Quando ad un controllo visivo dell'operatore, l'aria
è stata estratta completamente dal sacchetto,
premereil pulsante di saldatura
3
: si accenderà il
led di saldatura
4
e la macchina inizierà a saldare
il sacchetto;
7- Una volta terminata la saldatura del sacchetto, la
macchina si arresta. I led si spengono e il coperchio
si alza dopo pochi secondi.
VUOTO IN CONTENITORI
1- Alzare il coperchio mobile
C
posto nella parte
anteriore della macchina.
2- Posizionare l'estremità senza guarnizione
dell'apposito tubo per vuoto nei contenitori sul
piccolo ugello
F
.
3- Posizionare l'estremità con guarnizione dell'apposito
tubo per vuoto nei contenitori sul coperchio del
recipiente preposto.
4- Premere il pulsante
1
senza richiudere il coperchio
C
.
5- La confezionatrice si mette in funzione.
6- Il led
2
presente sul display si accende.
7- Al termine del ciclo di vuoto, ripremere il tasto
1
per tre secondi; la macchina si arresta senza attivare
la saldatura.
A
E
D
F
B
C
V
AC
UU
M
S E A L
1
3
2
4
MODEL FSV 32S
DISPLAY FUNCTIONS
1 - switch to start and stop vacuum process
2 - LED that shows blank in progress
3 - Button for the control of welding
4 - LED active welding
COMPONENTS
A-Body
B-Display
C-Cover
D-Teflon coated sealing blade
E-Seal
F-nozzle to make vacuum in containers
VACUUM BAGS
1- Connect the power plug to the power outlet, after
5 seconds, the machine will be active.
2- Lift the cover "
C
" located on the front of the machine.
3- Place the bag between the two seals lower "
E
"
making sure that the edge is free of rips and is well
supported on the floor.
4- Lower the cover "
C
" by applying light pressure
on the lateral ends.
5- Press the button
1
: the machine begins to draw
the air inside the bag and turns on the first LED
from the bottom
2
;
6- When a visual control of the operator, the air
has been completely removed from the bag
complete, press the button welding
3
: LED will light
welding
4
and the machine will start to pay off the
bag;
7- Once the welding of the bag, machine stops. The
LEDs are turned off and the lid gets up after a few
seconds.
VACUUM CONTAINERS
1- Lift the cover "
C
" located on the front of the
machine.
2- Place the end without gasket the special vacuum
tube in the containers on the small nozzle "
F
".
3- Place the end with the special seal vacuum tube
in the containers on the lid of container charge.
4- Press the
1
button without closing the cover "
C
".
5- The packaging machine is put into operation.
6- The LED
2
lights up on the display.
7- At the end of the vacuum cycle, press the switch
1
for three seconds, the machine stops without
activating welding.
Содержание FSV 32D
Страница 12: ......