FALK QUADRIVE JF Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 52

background image

Lubrication

CAUTION:

Drives shipped without oil.

14.

JR, JF & JSC —

Refer to Appendix A for selection of

lubricant. Refer to Table 9 for approximate oil capacity of
drives.

15.

JR, JF & JSC —

HORIZONTAL MOUNTING

Remove air vent and oil level plug (Refer to Step 1). Fill the
drive until oil shows in the oil level hole. Coat the air vent
and plug threads with #3 Permatex or equivalent thread
sealant before replacing.

JRV, JFV & JSCV —

(VERTICAL MOUNTING) - Refer to

Figure 1, Step 1.

Input Shaft DOWN —

Remove the fill plug and fill

with oil to level marked on the dipstick.

Input Shaft UP —

Remove the oil level and fill plugs

and fill until oil shows in the oil level hole.

Coat the plug threads with #3 Permatex or equivalent
thread sealant before replacing.

If stand pipe is used as oil fill, the intermediate cover plug
must be removed to eliminate entrapped air.

16.

JR, JF & JSC —

Where applicable, pump grease into the

input seal cover, Figure 10, until the grease appears at the
shaft. Wipe off excess grease from the shaft. DO NOT use
grease where it could contaminate the product e.g. foods,
drugs etc.

Start Up

17.

JR, JF & JSC —

Before operating the drive, check any fasteners,

pipe plugs, air vent, etc. which may have been loosened in the
course of Outfitting, Installing and Lubricating the drive, to be
sure that they have been properly retightened. Check correct
rotation of motor & backstop and be sure drive is properly
lubricated. After one week of operation repeat check of all
external fasteners and pipe plugs.

18. After one month of operation:

a) Operate the drive until the sump oil reaches normal

operating temperature. Shut the drive down and
drain immediately.

b) Immediately flush the drive with an oil of the same type

and viscosity grade as the original charge (warmed to
approximately 100°F in cold weather). Rapidly pour or
pump a charge equal to 25-100% of the initial fill thru
the drive, or until clean oil flows thru the drain.

c) Close the drain and refill the drive to the correct level

with new or reclaimed oil of the correct type and
viscosity. If determined to be in good condition by the
supplier, drain oil may be reused if it is filtered thru a
100 micron or finer filter.

The Falk Corporation, P.O. Box 492, Zip 53201-0492

378-102

3001 W. Canal St., Zip 53208-4200, Milwaukee, WI USA Telephone: 414-342-3131

August 2004

Fax: 414-937-4359 e-mail: [email protected] web: www.falkcorp.com

Supersedes 6-92

®

a good name in industry

Owners Manual

•

Quadrive Shaft Mounted Drives

(Page 8 of 56)

Sizes 4407/M4407-4608/M4608

Figure 10

TABLE 9 — Approximate Oil Capacity –

Gallons (Liters)

H

Drive Size

JR, JF & JSC

JRV & JFV

4407

4.3 (16,3)

6.3 (23,8)

4415

7.0 (26,5)

9.5 (36,0)

4507

10.3 (39,0)

13.3 (50,3)

4608

25.0 (94,6)

31.3 (118)

H

Quantities are approximate. Always fill drive to specified level.

«
...
6
7
8
9
10
...
»

Содержание QUADRIVE JF





















































Отзывы:

Нет отзывов

Похожие инструкции для QUADRIVE JF

Бренд: GALLERY Страницы: 18

Бренд: Zetec Страницы: 23

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: ParaBody Страницы: 5

Бренд: Haaga Страницы: 31

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды