This is required eventually for tying to the appliances
on the other side of the suite.
g) The plate from the hob underside is now used to tie
the bases of the joined units together at the front
behind the corner posts. See Figure 7.
h) Repeat above procedure until all models along one
side of the suite are assembled. Replace corner
posts, control knobs, flue, etc.
j ) Assemble the gas header pipe along the rear of the
appliances from the main isolating cock. Connect
tothe inlet pipe of each appliance.
k) Complete the other side of the suite, following the
same procedure. Ensure a flush, tight joint line
between the hobs.
CONNECT THE GAS HEADER TO EACH UNIT AS
BUILDING PROCEEDS
m) Secure a tie plate across the hob joint at each end
of the suite. Fit the service void end panels.
n) Check out each appliance in the suite as detailed in
Section 2.1.1.
Assembly Procedures (Wall Suites)
Procedure is generally as central suites. Depending
on proximity of rear wall or other units, the header
pipe may have tobe fitted as building proceeds.
2.2 CONNECTION TO A GAS SUPPLY
The gas supply piping and connection to the
appliance must be installed in accordance with the
various regulations listed on the cover of this
document. on natural gas appliances, the adjustable
governor MUST be fitted to the supply, securely fixed
in a position which will enable adjustments to be
made during commissioning. On propane appliances,
a governor must not be fitted.
2.3 CONNECTION TO AN ELECTRICITY SUPPLY
Not applicable to these models.
2.4 CONNECTION TO A WATER SUPPLY
Not applicable to these models.
2.5 PRE-COMMISSIONING CHECK
After installation, the engineer should check that all
gas connections are sound and do not leak, and that
the unit is operating satisfactorily before leaving the
kitchen.
2.6 INSTRUCTION TO USER
After installing and commissioning the appliance,
please hand the User's Instructions to the user or
purchaser and ensure that the person(s) responsible
understands the instructions for lighting, turning off,
and correct use and care of the appliance.
It is important to ensure that the location of the gas
isolating cock is made known to the user, and that the
procedure for its operation in an emergency is
demonstrated.
SECTION 3 - SERVICING AND
CONVERSION
Important
BEFORE ATTEMPTING ANY SERVICING,
ENSURE THAT THE ISOLATING COCK IS
T U R N E D O F F A N D C A N N O T B E
INADVERTANTLY TURNED ON.
AFTER ANY MAINTENANCE TASK, CHECK THE
APPLIANCE TO ENSURE THAT IT PERFORMS
CORRECTLY AND CARRY OUT ANY NECESSARY
ADJUSTMENTS AS DETAILED IN SECTION 1.
After carrying out any servicing or exchange of gas
carrying components -
ALWAYS CHECK FOR GAS SOUNDNESS!
3.1 CONVERSION
For conversion to NATURAL GAS, fit the correct
governor and set the burner pressure.
For conversion to PROPANE GAS, remove the
governor from the gas circuit.
Other considerations -
CHANGE INJECTORS
OVEN ONLY - ADJUST BYPASS SCREW AND SET
LOW RATES
CHANGE DATA PLATE
3.2 REMOVAL OF PANELS
3.2.1 RH Outer Panel
Remove the fixings which secure the panel bottom
flange tothe underside of the base. Slide panel back
to withdraw the two pins which locate the rear of the
vertical control panel. Pull the panel out slightly at the
bottom then draw it down to clear the top flange which
engages under the lip on the hob edge. Replace in
reverse order.
3.2.2 Bottom Front Panel
Lift to unhook and lower. Undo the lower RH hinge pin
and remove the panel. Replace in reverse order.
3.2.3 Vertical Control Panel
Pull off the control knobs. Remove the fixings which
secure the panel bottom flange to the base plate.
Withdraw the panel outward slightly at the bottom to
clear the control spindles and pull it down to free the
top locating flange. Replace in reverse order.
3.2.4 Top Facia Panel
Open Tops
Remove pan supports. Undo the fixings which secure
the control panel to the hob support from inside the
unit. Replace in reverse order.
Solid Tops
Remove all plates, bullseyes and cups. Undo the
control panel fixings from inside the unit. Undo the
fixings which secure the control panel to the hob
support. Replace in reverse order.
