Falcon Elan 110 Dual Fuel, Руководство пользователя и инструкции по установке

Страница: 37 / 44

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
33
Remove the 2 rear hotplate fixing screws ‘B’ on the
cooker back under the flue grille, and the 4 front
hotplate fixing screws ‘A’,
(Fig.9-3)
.
Remove the screws holding the flue grille stays.
Lift the hotplate clear of the appliance.
Reassemble in reverse order, making sure that the leads
are reconnected.
Check for correct burner operation.
2.2 To Change a Hotplate Tap
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Unplug the FSD lead
from the rear of the tap and undo the compression
fitting. Remove the fixings that secure the tap to the gas
rail. Remove the tap. Remove and discard the gasket
seal.
Fit the new gasket seal to the replacement tap.
Reassemble in reverse order.
Make sure that the valve is adjusted for correct gas
operation. Check that the cooker is gas sound. Check
hotplate ignition.
2.3 To Replace a Hotplate Burner Jet
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the burner cap and head (Fig.9-4) . Remove the
old jet. Fit the new orifice.
Note: The wok burner has 2 orifices.
Reassemble in reverse order. Check that the appliance is
gas sound.
2.4 To Change a Hotplate Burner Electrode
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Lift off the pan supports and remove the burner cap.
Remove the screw holding the electrode. Pull the
electrode vertically up sufficiently to grip the lead
between thumb and forefinger. Pull off the electrode,
but keep hold of the lead.
Fit the new electrode to the lead. Fix the electrode in
the burner with the screw. Replace the burner cap.
Check the burner ignition. Replace the pan supports.
2.5 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one
side. Ensure that the thermocouple is cool. Turn the
thermocouple so that the earth lead (no sleeve) is in line
with the slot. Lift the thermocouple clear of the hole.
Reassemble in reverse order.
2.6 To Remove or Change a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Remove the control
panel (see 1.2).
Centre Hotplate Burners
The burners are mounted in pairs on the cross supports.
Disconnect the burner feed pipes at the burners.
Remove the screw at the front holding the cross support
(Fig.9-5)
. Slide the support to the right to release it from
the rear location.
Lift the cross support and burners clear. The burners
are fixed to the cross supports with screws underneath.
Remove the appropriate burner and fit the new one.
Reassemble in reverse order. Check that the burner
operation is satisfactory.
Wok Burners
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check that
the burner operation is satisfactory.
3 Controls
3.1 To Change Ignition Generator
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Pull the cooker forward to gain access to the cover box
at the rear of the left-hand oven. Remove the screws
securing the cover and lift clear. Pull off all the leads
to the generator, noting their positions. Slacken the
2 screws holding the generator to the cooker and
remove the generator.
Fit the new generator to the cooker and replace the
leads, referring to the wiring diagram.
Reassemble in reverse order. Check ignition
performance.
3.2 To Replace the Light Switch
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the
switch body behind the control panel and twisting
sharply. Remove the switch bezel by folding back its
locking wings and pushing forward.
Fit the new bezel to the control panel by first lining up
the raised key on its body with the cut-out in the control
panel and pushing it in from the front.
Assemble the new switch to the bezel by lining up the
key sections and pushing home. Fit the new button by
pushing in from the front.
Replace the control panel in reverse order and test for
correct operation.