Fagor MCS Innova Series Скачать руководство пользователя

Страница: 13 / 88

Digital Brushless AC servo drive system - Ref.0707

MCSi-13/84

Brake characteristics

FSA and FSP series motors have an optional brake that applies friction to the shaft. Its
purpose is to immobilize or lock vertical axes, not to brake a moving axis. Its main
characteristics depending on the type of brake are:

Brake

Holding

torque

Power

consumption

Supply

voltage

Mass

Inertia

Motor type

Nm (lbf· In)

W (hp)

V DC

kg (lbf)

kg·cm

FSA01

0.318 (2.814)

6.0 (0.008)

0.300 (0.66)

0.0085

FSA02

0.637 (5.637)

6.9 (0.009)

0.500 (1.10)

0.058

FSA04

1.270 (11.240)

6.9 (0.009)

0.500 (1.10)

0.058

FSA08

2.390 (21.153)

7.7 (0.010)

0.900 (1.98)

0.058

FSP01

0.318 (2.814)

8.1 (0.010)

0.200 (0.44)

0.029

FSP02

0.637 (5.637)

7.6 (0.010)

0.500 (1.10)

0.109

FSP04

1.270 (11.240)

7.6 (0.010)

0.500 (1.10)

0.109

FSP08

2.390 (21.153)

7.5 (0.010)

1.500 (33.1)

0.875

The brake must not be used to stop the axis while it is moving.

The brake must never exceed its maximum turning speed.

A voltage between 22 V and 26 V releases the shaft. Make sure that
no voltage over 26V is applied that prevent the shaft from turning.

When installing the motor, make sure that the brake fully releases
the shaft before making it turn for the first time.

BASE FEEDBACK CONNECTOR

On FSA and FSP motors (200 V)

Note 1. The rest of pins are not connected

Signal

Pin

Color

0 V (16 bit absolute)

Pink

3.6 V (16 bit absolute)

Grey

+ RS485

Green

- RS485

Yellow

+ 5 V

White

0 V

Brown

Note 2. Connector housing connected to ground

Viewed from the outside of the motor

Содержание MCS Innova Series

























































































Результаты поиска

Содержание MCS Innova Series

Отзывы:

Похожие инструкции для MCS Innova Series

Бренды по названию

Популярные бренды

Fagor MCS Innova Series, Руководство пользователя

Результаты поиска

Содержание MCS Innova Series

Отзывы:

Похожие инструкции для MCS Innova Series

Бренды по названию

Популярные бренды