Fagerhult e-Sense Actilume Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 9

Fagerhult e-Sense Actilume Скачать руководство пользователя страница 9

Dokumentet kan ändras utan föregående meddelande. Subject to change without notice.

Programming with IRT 8099/00 or IRT 9090/00

Actilume systems for light adjustment consist of a small,
compact sensor and a control unit designed for installation in
fixtures. Actilume is a simple system produced for plug and
play lighting solutions, mostly in office environments. A sus-
pended fixture, an open plan office solution with nine fittings,
or, for example, an office room with four fixtures, are perfect
for controlling with Actilume. Actilume uses a master–slave
control, which is easy to install, deploy and use.

NOTE! Important!

Philips has updated the Actilume system and has added
functions for Philips OccuSwitch DALI also. This means that
the programming tool IRT 8099/00 has been replaced with
IRT 9090/00 with effect from 2014. All the original program-
ming functions are the same, but the new functions cannot be
programmed into Actilume generation 1, which Fagerhult uses
in all its fixture solutions.

The manual describes how to program using IRT 8099/00;
the positions of the buttons may have changed in the newer
IRT 9090/00 but the functions are the same. The functions
available in IRT 9090/00 that cannot be programmed are the
following (used only in OccuSwitch DALI):

•  I/II Funktion
•  Config.
•  Link
•  DALI prog.
•  Delay
•  PIR
•  Daylight
•  RF channel

IRT8099/00

IRT9090/00

9

«
...
7
8
9

Содержание e-Sense Actilume










Отзывы:

Нет отзывов