manualshive.com logo in svg
background image

- 22 -

GB

Strabuc 918 and Strabuc 930

PIC. 6

PIC. 7

PIC. 8

INSTALLATION OF THE 

STRABUC 918

 OR 

STRABUC 930

 TRAFFIC CONTROL POST

INSTALLATION OF THE 

STRABUC 930 HEAVY ARMOURED

 (WITH ARMOURED LOCK BARREL)

Once the cement has set, proceed with installation of the
traffic control post inside the 

cylindrical container

.

For this operation, it is necessary to use equipment suitable
for hoisting and then placing it in the post seat, by hitching
to the 

eyebolt

 on the top of the 

retracting post cover

,

having unscrewed and removed the three screws and the

cover

. Before placing the Strabuc 930 inside the cylindrical

container, pass all the electric wires through the corrugated
tube connected to the Elpro S40 programmer: for this initial
phase, use a pull-out to be passed through the pipe first
(Pic. 6 and Pic.10).

Before installing the Strabuc 930 Heavy Armoured version (with 

Armoured Lock Barrel

) the traffic post must be connected to the 230 Volt power supply (

1

).

Raise the post about 

20 cm

 (

2

) and switch off the power supply (

3

) (Pic.7).

N.B.

 We recommend to fit a 20 μF capacitor in parallel to the two phase/live wires to give the traffic control post more power on starting.

M10x30 hexagonal
socket head post
cover fastening
screws

Rubber edge

Drilled flange for
edge tightening

Eyebolt

Protection
cap

Armoured

lock barrel

Personalised

key

Triangular
profile key

about

20 cm

Connect the traffic control post
to the 230 Volt power supply

20 μF

capacitor

CONNECT

the 230 V

power supply

DISCONNECT

the 230 V power supply

and drain the capacitor

20 μF

capacitor

Eyebolt

Under the retractable post cover,

there is an eyebolt for easy hoisting

1)

4)

5)

Raise the post about 20 cm, to allow
the subsequent extraction of the
reinforced lock barrel

N.B.

 If the post lowers instead of rising, switch over

the electric wires of the two “phases”, leaving the
“common” in place.

2)

Once the post has been raised,

switch off

 the power supply

3)

Strabuc 930

Heavy Armoured

Strabuc 930

Heavy Armoured

Strabuc 930

Heavy Armoured

Strabuc 930

Heavy Armoured

Strabuc 930

Heavy Armoured

Содержание Strabuc 918

















Отзывы: