background image

I n s t a l l a t i o n   I n s t r u c t i o n s

1 1

Points to note for build-in and finishing: 

A = installation reference markers (fig. 2.5)

S, T and Q = decorative frames (fig. 2.6) 

If the reference markers are not removed, after installation the 

decorative frames will not fit!

Always install the combustion air supply grilles in the false chimney 

breast (fig. 1.1).

4.5  

Mounting the decorative frames 

• 

First, install the bottom decorative frame piece (fig. 2.6 Q).

• 

Then install the left and right decorative frame pieces 

 

(fig. 2.6 S), these are held in place by the adjustable  

 

 

magnetic snappers.

• 

Now install and tighten the top frame (fig. 2.6 T)

4.6 4 

Seasons Premium with mantelpiece 

Keep in mind the build-in measurements and the minimum fireplace 

opening measurement (see size drawing and fig. 2.5)

5 Checking the technical installation 

5.1  

Initial use of the fire

When using the fire for the first time, always use the remote control. 

The unit must not be linked to the Wi-Fi and App.

Upon leaving the factory, the remote control is already linked to the 

fireplace.

You must manually open and close the door before igniting the fire. 

To this end, switch on the service mode switch (fig 1.2B and fig 1.8 

I). The LED on the ITC will now start to flash in orange to indicate 

that the fire is in service mode!

You can now open the door with the push-button (fig 1.2 H, fig 

1.8L). Keep in mind that when the door opens for the first time, it 

will open slowly. If you hear any strange noises, immediately stop 

using the unit and determine the cause. After the door has fully 

opened, press the push-button to close the door again (fig 1.2G, fig 

1.8M). Then open the door again and install the decorative material 

and the logs.

Now turn off the service mode switch.

See also user’s manual ITC 4Seasons Premium 

If required, bleed the gas line!

5.2   

Service mode

This function is only used for servicing purposes and in case the 

window or door remains stuck in a certain position after a power 

outage. You can close the door again when in service mode. The 

fireplace will continue to work as usual again after leaving the 

service mode.

For the operation of the service mode, see 5.1 initial use.

5.2.1 

Placing the decoration material

It is not permitted to use other or to add more material in the 

combustion chamber.

Always keep the ignition and ionisation pins clear of all 

decorative material! 

Do not pour all decorative material on to the burner at once; it can 

get clogged because of dust particles.

5.2.1.1   Wood set 

• 

Place the ionisation cover (fig.4.1A) 

• 

Place some of the chips on the burner and on the bottom.

• 

Places the wood blocks as prescribed. (Fig. 4.1 of included   

 

wood set card) 

• 

Divide the rest of the chips on the burner and on the bottom.  

 

Prevent a thick layer on the burner; this adversely affects the  

 

fire image.

• 

Manually close the window by pressing the push-button    

 

(fig1.2G and fig 1.8M).

• 

Now turn on the service mode switch again (fig1.2B and fig   

 

1.8I)

5.2.2 

Checking the ignition on the main burner and the   

 

 

flame spread.

Start the ignition procedure according to the instructions in the 

user’s manual. 

If the burner fails after the first ignition procedure (15 seconds), you 

must reset the electronics. 

Reset: via the remote control

function button: 2+5 (fig4.2)

• 

Always wait for 5 minutes before restarting the fireplace.

• 

After a third reset, an automatic obstruction of 15  

 

 

minutes is programmed; you can start the unit again    

 

after these 15 minutes. 

• 

Check whether the ignition on the main burner occurs rapidly  

 

and smoothly

• 

The middle part of the main burner will automatically start to  

 

burn on the middle (high flame) setting. 

• 

Use the remote control to switch the fireplace to the desired  

 setting.

• 

Evaluate the flame spread by letting the fireplace work on    

 

both wide and high flame settings.

TIP: You can move around some of the decorative material to 

obtain the best flame spread.

5.2.3 

Checking for gas leaks 

Check with a gas leak finder or spray all connections and pipes for 

gas leakage. 

PLEASE NOTE: Make sure to dry all the components    

 

checked with spray.

Содержание 4Seasons Premium

















Отзывы: