FAAC FSL700 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

FAAC FSL700 Скачать руководство пользователя страница 14

14

Limit Switch Setup

The gate operator uses a limit switch assembly to adjust the dis-

tance of travel. These adjustments should be made before power

is supplied to the operator. To adjust the distance of travel using

the limits:
1. Turn power OFF! Use the power switch on the side to assure

AC and Battery power are both OFF.

2. Manually move the gate fully to the right. Push the limit guide

plate down and roll the top limit nut until it activates the top limit

switch. The switch will click when activated.

3. Manually move the gate to the left. Push the limit guide plate

down and roll the bottom limit nut until it activates the bottom

limit switch. The switch will click when activated.

4. Release the limit guide plate and make sure it is engaged in

the slots of each limit nut.

5.

Readjust the limit nuts as necessary to fine tune the full-open

and full-closed positions.

RIGHT

LEFT

Gate Operator Direction

The gate operator uses a DIP switch setting to determine the open and close direction. To set the Open/Close direction:
1.  Turn power OFF! Use the power switch on the side to assure AC and Battery power are both OFF.
2.  Standing inside the gate looking at the gate operator, determine if the gate opens to the LEFT or RIGHT.
3.  If the gate opens to the LEFT, move DIP SWITCH 6 to the Left.
4.   If the gate opens to the RIGHT, move DIP SWITCH 6 to the Right.

Opens LEFT

Opens RIGHT

Monitor Photo / Edge

Anti-Tailgate

Master / Slave

Close Timer

Power Fail Open / Cycle

Open Left / Right

Quick Close

Stop (NC / NO)

Low Battery Cycle / Open

Mag / Solenoid Delay

Monitor Close / Op-Cl

Soft Start / Hard Start

Off On

DIP SWITCH 6

Monitor Photo / Edge

Anti-Tailgate

Master / Slave

Close Timer

Power Fail Open / Cycle

Open Left / Right

Quick Close

Stop (NC / NO)

Low Battery Cycle / Open

Mag / Solenoid Delay

Monitor Close / Op-Cl

Soft Start / Hard Start

Off On

DIP SWITCH 6

«
...
12
13
14
15
16
...
»

Содержание FSL700

































Отзывы:

Нет отзывов