![background image](http://html1.mh-extra.com/html/faac/b680/b680_manual_3189663004.webp)
ENGLISH
WARNINGS FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
1) ATTENTION! To ensure the safety of people, it is important that you
read all the following instructions. Incorrect installation or incorrect
use of the product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product..
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of
children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this do-
cumentation. Any other use, not expressly indicated here, could compromise
the good condition/operation of the product and/or be a source of danger.
6) FAAC declines all liability caused by improper use or use other than that for
which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of
infl ammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605. For non-EU countries, to obtain an adequate level of safety,
the Standards mentioned above must be observed, in addition to national
legal regulations..
9) FAAC is not responsible for failure to observe Good Technique in the con-
struction of the closing elements to be motorised, or for any deformation that
may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. For
non-EU countries, to obtain an adequate level of safety, the Standards men-
tioned above must be observed, in addition to national legal regulations..
11) Before attempting any work on the system, cut out electrical power.
12) The mains power supply of the automated system must be fi tted with an
all-pole switch with contact opening distance of 3mm or greater. Use of a
6A thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fi tted upstream
of the system.
14) Make sure that the earthing system is perfectly constructed, and connect
metal parts of the closing elements to it.
15) The automated system features a built-in anti-crushing safety device consisting
of a torque control. It is however necessary to check its tripping threshold,
as provided for in the Standards described in point 10.
16) The safety devices (EN 12978 standard) protect any danger areas against
mechanical movement Risks, such as crushing, dragging, and shearing.
17) For each system, we recommend using at least one signal light (e.g.: FAA-
CLED or integrated fl ashing traffi c light) as well as a warning sign securely
fi xed to the structure, together with the devices described in point “16”.
18) FAAC declines all liability as concerns safety and effi cient operation of the
automated system, if system components not produced by FAAC are used.
19) For maintenance, strictly use original parts by FAAC.
20) Do not in any way modify the components of the automated system
21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the User the leafl et
supplied with the product.
22) Do not allow children or adults to stay near the product while it is operating.
23) Keep radio controls or other pulse generators away from children, to prevent
the automated system from being activated involuntarily.
24) Transiting is permitted only when the automated system is stationary.
25) The User must not attempt any kind of repair or direct action whatever and
contact qualifi ed personnel only.
26) Maintenance: check at least every 6 months the effi ciency of the system,
particularly the effi ciency of the safety devices (including, where foreseen,
the operator thrust force) and of the release devices.
27) Anything not expressly specifi ed in these instructions is not permitted.
EC DECLARATION OF CONFORMITY
The Manufacturer
Company name:
FAAC S.p.A. Soc. Unipersonale
Address:
Via Calari, 10 - 40069 Zola Predosa BOLOGNA
- ITALY
hereby declares that the following products:
Description:
Vehicular barrier
Model:
B680H
comply with the following applicable EU legislations:
EMC Directive 2014/30/EU
Directive ROHS 2 2011/65/EU
Furthermore, the following harmonised standards have been ap-
plied:
EN 61000-6-2:2005
EN 61000-6-3:2007 + A1:2011
Bologna, 01-01-2016 CEO
DECLARATION OF INCORPORATION OF PARTLY COMPLETED
MACHINERY
(2006/42/EC ANN.II P.1, LETT. B)
Manufacturer and person authorised to prepare the relevant tech-
nical documentation
Company name:
FAAC S.p.A. Soc. Unipersonale
Address:
Via Calari, 10 - 40069 Zola Predosa BOLOGNA
- ITALY
hereby declares that for the partly completed machinery:
Description:
Vehicular barrier
Model:
B680H
the following essential requirements of the Machinery Directive
2006/42/EC (including all applicable amendments) have been
applied and met:
EHSR 1.1.2, 1.1.3, 1.1.4, 1.1.5, 1.1.6, 1.1.7, 1.2.1,
1.2.2, 1.2.3, 1.2.3.4, 1.2.4, 1.2.5, 1.3.1, 1.3.10,
1.3.12, 1.3.2, 1.3.3, 1.3.4, 1.3.6, 1.3.7, 1.3.8, 1.3.9,
1.4.1, 1.4.11, 1.4.13, 1.4.15, 1.4.5, 1.4.6, 1.4.7,
1.4.8, 1.4.9, 1.5.3, 1.6.1, 1.6.1.1
and that the relevant technical documentation has been compiled
in compliance with part B of Annex VII.
Furthermore, the following harmonised standards have been applied:
EN 12100:2010
EN 60335-1:2012 + A11:2014
EN 13849-1:2008
EN 13849-2:2008
Other technical standards applied:
EN 12453:2000
It is also declared that the partly completed machinery identified above
may not be commissioned until the final machine - into which it will be
incorporated - has been declared complaint with the provisions of the
above mentioned Machine Directive 2006/42/EC.
Bologna, 01-01-2016 CEO
Содержание B680
