![background image](http://html1.mh-extra.com/html/faac/940sm-series/940sm-series_manual_3188783039.webp)
38
ENGLISH
ENGLISH
TIME BAND 3: FUN 8 7 p.m.
TIME BAND 4: FUN 0
TIME BAND 5 : FUN 0
Select SAT and set the following:
TIME BAND 1: FUN 0
TIME BAND 2: FUN 0
TIME BAND 3: FUN 0
TIME BAND 4: FUN 0
TIME BAND 5: FUN 0
Select SUN and set the following:
TIME BAND 1: FUN 0
TIME BAND 2: FUN 0
TIME BAND 3: FUN 0
TIME BAND 4: FUN 0
TIME BAND 5: FUN 0
---------------------------------------------------------------------------------
ACCESSORIES
ACCESSORIES
ACCESSORIES
ACCESSORIES
ACCESSORIES
LLLLLOCK
OCK
OCK
OCK
OCK
Lock card installation procedure:
•cut mains power;
•insert the lock card in any of connectors J11, J12, J13 of
the 940SDM control board;
•make the electric connections;
•restore power.
Note
: to avoid damaging the lock card, always insert it
when power is OFF.
In the standard configuration:
- the lock locks the leaves only in the Night operating
function.
- if operating on batteries in the Night mode, if the batteries
become discharged, the lock continues locking the
leaves.
By using SD-Display, you can change lock
operation.
BROWN
WHITE
YELLOW
WHITE
BROWN
GREEN
PINK
J11/J12/J13
940SDM
LLLLLOCK SUR
OCK SUR
OCK SUR
OCK SUR
OCK SURVEILLANCE
VEILLANCE
VEILLANCE
VEILLANCE
VEILLANCE
This accessory enables a check of lock efficiency and, in
the event of an error, this is signalled by the SD-Keeper.
To activate lock surveillance, the function must be set with
SD-Display.
ANTI-P
ANTI-P
ANTI-P
ANTI-P
ANTI-PANIC WITH ELASTIC
ANIC WITH ELASTIC
ANIC WITH ELASTIC
ANIC WITH ELASTIC
ANIC WITH ELASTIC
The “Kit elastic” is a mechanical accessory enabling
opening of the leaves in case of a black-out.
To ensure the system operates correctly, the SD-Keeper
must be permanently installed.
Elastic kit installation procedure:
•supply mains power to the door;
•execute the Setup;
•activate the elastic kit with SD-Display;
•install the accessory mechanically.
After installation, the leaves will open when mains power
fails; when mains power is restored, the elastic must be
“reset”.
Resetting ca be done in two different ways (selected with
SD-Display):
- manually (STANDARD),
- automatically (NO STANDARD).
Resetting entails re-closing the leaves in order to apply
tension to the elastic and re-connect it to the electric
magnet (re-connection occurs with the leaves totally
closed and the 940SDM control board powered).
If manual resetting is selected, when mains power is
restored, the door is in manual mode, and this mode
cannot be exited until the leaves are totally re-closed
manually.
If automatic resetting is selected, when mains power is
restored, the control board activates a leaf closing
procedure, using much greater power than is usually
required for movement; furthermore, the ANTI-CRUSHING
DEVICE IS NOT ACTIVE during this procedure.
During the automatic procedure for resetting the elastic:
•if the photocells intervene, the door reopens and the
disengagement procedure begins;
•the sensors are disabled;
•any Setup requests are ignored.
IMPORTANT:
- NEVER carry out a Setup procedure if the elastic has not
been reset,
- do not install the batteries with this accessory.
ANTI-P
ANTI-P
ANTI-P
ANTI-P
ANTI-PANIC B
ANIC B
ANIC B
ANIC B
ANIC BY BREAK
Y BREAK
Y BREAK
Y BREAK
Y BREAK-OUT
-OUT
-OUT
-OUT
-OUT
This accessory enables the leaves to be opened by
pressure; to install it, refer to the specific instructions.
If installing the anti-panic by break-out facility, a sensor
(according to Standards prEN12650-1 and prEN12650-2)
must be installed. It must be connected to the EMERG1
input (via SD-Display) configured for commanding
immediate stop of the movement.
햲
햳
햴
Monitoring
sensor
햳
Lock release microswitch
햴
Lock monitoring microswitch
햲
햳
햴