English |
73
ELC 40/2400 PLUS
www.ffgroup-tools.com
ENGLISH
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
RECOMMENDED ACTIONS
Motor stops while
cutting
Chain pinched in cut
Undercut limb to relieve pressure on limb.
Cord is damaged or
severed
If extension cord is damaged, do not use and replace it.
If chainsaw cord is damaged, do not use and contact an
approved service location.
Chain brake is engaged
Set the front hand-guard to the operating position.
Motor does not run or
runs intermittently
Saw is not plugged in
Plug in the saw
Cord is damaged or severed
If extension cord is damaged, do not use it but replace it.
If chainsaw cord is damaged, do not use it but contact an
approved service location.
Bad electrical outlet
Plug extension cord into a different outlet.
Chain brake engaged
Set the front hand-guard to the operating position.
Trigger lock-out not pressed
Press the trigger lock-out before squeezing the trigger
switch
Debris in side cover
Unplug the chainsaw, then remove side cover and clean
out debris.
Motor does not stop
when chain brake is
engaged
Debris preventing full movement
of front handguard
Clean debris from external chain brake mechanism.
Possible chain brake malfunction
WARNING:
Operating a chainsaw without a functioning
chain brake could lead to serious personal injury. Contact an
approved service location before using.
Motor runs, but saw
chain does not rotate
Chain not engaging drive
sprocket
Reinstall the chain, making sure the drive links on the chain
are fully seated on the drive sprocket.
Guide bar nose sprocket is not
turning
Replace the guide bar.
Chainsaw does not cut
properly
Insufficient chain tension
Tension the chain.
Dull chain
Sharpen the chain.
Chain installed backwards
Install the chain with the teeth facing the correct direction.
Worn chain
Replace the chain.
Dry or excessively stretched chain
Check the oil level. Refill oil reservoir if necessary.
Chain not in bar groove
Reset chain onto groove.
Chain loosening or com-
ing off of guide bar
Side cover not installed correctly
Properly install side cover ensuring the tab at rear of side
cover is tucked into saw body.
Bar and chain excessive-
ly hot and/or smoking
Chain is under-lubricated
Check the oil level. Refill oil reservoir if necessary.
Содержание ELC 40/2400 PLUS
