F.F. Group AG 230/2400S PRO, Оригинальное руководство пользователя

Страница: 13 / 60

English | 13
www.ffgroup-tools.com
AG 230/2400S PRO
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.
TECHNICAL DATA
Article number 41 631
Model AG 230/2400S PRO
Rated voltage
V 230-240
Hz 50/60
Rated power input W 2.400
Rated speed min -1 6.600
Grinding disc diameter,
max.
mm 230
Thread of grinder spindle M 14
Weight kg 5,0
Sound emission values determined according to
EN 60745-1, EN 60745-2-3
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 95
Sound power level dB(A) 106
Uncertainty K dB 3
Vibration total values a
h
(triax vector sum) and
uncertainty K determined according to
EN 60745-1, EN 60745-2-3
Vibration level max:
a
h,AG
m/s
2
11,862
K m/s 2 1,5
NOISE/VIBRATION INFORMATION
The vibration level given in this information sheet
has been measured in accordance with a standard-
ized test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure. The declared
vibration emission level represents the main appli-
cations of the tool. However if the tool is used for
different applications, with different accessories or
insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organization of work patterns.
IDENTIFICATION
1. On/Off switch
1a. Safety lock-out
2. Spindle lock button
3. Auxiliary handle
4. Protective guard
5. Release lever for protection guard
6. Spindle
7. Clamping flange
8. Spanner
9. Mounting flange
USE
MOUNTING OF ACCESSORIES (E)
h
Clean spindle (06) and all parts to be mounted.
h
Tighten clamping flange (07) with spanner (08) while
pushing spindle-lock button (02) .
h
For removing accessories handle vice-versa.
MOUNTING OF AUXILIARY HANDLE (D)
Screw auxiliary handle (03) on the right, the top, or
the left of the tool (depending on the work to be
carried out).
REMOVING / MOUNTING / ADJUSTING OF PRO-
TECTIVE GUARD (C)
h
Place protective guard (04) on the spindle collar of the
tool head and turn it to the required position (depend-
ing on the work to be carried out).
h
If necessary, adjust protective guard (04) by tighten-
ing screw which is pre-set at manufacturing.
BEFORE USING THE TOOL
h
Ensure that accessory is correctly mounted and firmly
tightened.
h
Check if accessory runs freely by turning it by hand.
h
Test-run tool for at least 60 seconds at highest no-load
speed in a safe position.
h
Stop immediately in case of considerable vibration or
other defects and check tool to determine the cause.
SWITCHING ON AND OFF (Β)
h
Switching on the device:
ƒ
Press the safety lock-out (01a) .
ƒ
Then press the ON / OFF switch (01) .
h
Switching off the device:
ƒ
Release the ON / OFF switch (01) .
ROUGH GRINDING
h
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the ma -
chine back and forth with moderate pressure. In this
manner, the workpiece will not become too hot, does
not discolor and no grooves are formed.
h
Never use a cutting disc for roughing.
CUTTING
h
Do not tilt the tool while cutting.
h
Always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner.
h
Do not apply pressure on the tool; let the speed of the
cutting disc do the work.
h
The working speed of the cutting disc depends on the
material to be cut.
h
Do not brake cutting discs with side pressure.
MAINTENANCE
Regular inspection and cleaning reduces the neces -
sity for maintenance operations and will keep your
tool in good working condition. The motor must be