F.F. Group 47 484, Оригинальное руководство пользователя

Страница: 10 / 36

| English 10
4. Non-intended use.
5. Electrical system breakdown due to power of
the machine in a manner not compliant with the
electric and VDE regulations.
TECHNICAL DATA
Article Number 47 484
Model EXTREMIG 200
Voltage V 230
Frequency Hz 50/60
Max rated input current A 36
Rated capacity kVA 8.3
No load voltage V 68
Welding voltage V 15,5~24
Rated duty cycle 15%
Welding Wire diameter mm 0,6 - 1,0
Wire feed speed
m/
min
2 - 10
Rated welding current (MIG) A 200
Current adjustment (MIG) A 30 - 200
Rated welding current
(STICK)
A 170
Current adjustment (STICK) A 30 - 170
Insulation grade F
IP IP21S
Cooling Air
Weight kg 11
Dimension (LxWxH) cm 49,4x22x38
IDENTIFICATION (FIG. 1)
1. Control panel
2. Ground lead output
3. Possitive lead output
4. MIG output
5. ON/OFF switch (other side)
OPERATION
PREPARING THE UNIT
Unpacking and completing the assembly should
be done on a flat and stable surface, with enough
space for moving the machine and its packaging,
always making use of suitable equipment.
WARNING
Always unplug your machine from power source be -
fore any adjustment.
OPERATING THE UNIT
WARNING
Connect ground lead as close to the area being weld-
ed as possible to ensure a good ground. Do not allow
any body part to come in contact with the welding
wire if you are in contact with the material being
welded, ground or electrode from another welder.
Do not drape cables over or around your body. Do
not overuse or overheat your welder. Allow prop -
er cooling time between duty cycles. Do not point
torch at any body part of yourself or anyone else.
Always use this welder in the rated duty cycle to pre-
vent excessive heat and failure.
On the machine you will find the data table with
the below information:
X = Duty cycle
I1max = Maximum rated input current
I1eff = Maximum effective input current
I2 = Rated welding current
U0 = No load rated voltage
U1 = Rated input voltage
U2 = Loading voltage
NOTE
Suitable welding wire diameter should be selected
according to the welding job about to undertake.
MAINTENANCE AND CLEANING
WARNING
For your own safety, turn the switch off and remove
plug from power source outlet before any operation
of maintenance on the machine.
Keep your appliance clean. In order to avoid
overheating of the motor, regularly check the air
openings for any dust sticking on. After a longer
period of use, it is recommended to have the ma -
chine checked by an authorized dealer service.
Connections and repairs of electrical equipment
may only be carried out by an electrician.
POWER CORD
To avoid shock or fire hazard, if the power cord is
worm or cut, or damaged in any way, have it re -
place immediately. Electrical connection cables
often suffer insulation damage. Possible causes
are:
f
Punch points when connection cables are run
through window or door gaps.
f
Kinks resulting from incorrect attachment or lay -
ing of the connection cable.
f
Cuts resulting from running over the connecting
cable.
f
Insulation damage resulting from forcefully pull -
ing out of the wall socket.
f
Cracks through aging of insulation.
Such defective electrical connection cables must
not be used as the insulation damage makes them
extremely hazardous.
CLEANING
Use a small soft brush to clean the outside of the
unit. Do not use strong detergents. Household
cleaners that contain aromatic oils such as pine
and lemon and solvents such as kerosene can
damage plastic housing or handle. Wipe off any
moisture with a soft cloth. Remove dust, dirt and
machining residues with an appropriate vacuum
cleaner if necessary.
EXTREMIG 200