EZZE MASS2 Скачать руководство пользователя страница 49

Страница: 49 / 137

Model

MASS 2

Version

V_1.0

Prepared by

H/W

Date

22/01/2008

Subject Technical

Manual Page

27/59

-. The NFI core can automatically generate ECC parity bits when programming or reading the device.

-. Used 7 control Signal : NRE#, NEW#,NCE#,NALE, WATCHDOG#,NCLE, NRNB.

6.3

USB Device controller

The MT6225 provides a USB function interface that is in compliance with Universal Serial Bus (USB) Specification Rev 1.1

The USB device controller supports only full-speed (12 Mbps) operation. The cellular phone uses this widely available USB

interface to transmit/receive data with USB hosts, typically PC/laptop.

Figure 22. USB Interface Circuit

6.4

Memory Stick and SD Memory Card Controller

The controller fully supports the Memory Stick bus protocol as defined in Format Specification version 2.0 of Memory Stick

Standard (Memory Stick PRO) and the SD Memory Card bus protocol as defined in SD Memory Card Specification Part 1

Physical Layer Specification version 1.0 as well as the MultiMediaCard (MMC) bus protocol as defined in MMC system

specification version 2.2. Since SD Memory Card bus protocol is backward compatible to MMC bus protocol, the controller is

capable of working well as the host on MMC bus under control of proper firmware. Furthermore, the controller also support

SDIO card specification version 1.0 partially. However, the controller can only be configured as either the host of Memory

Stick or the host of SD/MMC Memory Card at one time.

MASS 2

is not interfaced Mini SD card but T-Flash Memory Card.

Interface Signals are same. Normally, the Detection is controlled by INS pin status. When Card is nothing, The INS is high

logically. And When Card inserted, The INS is low.

Pin Assignment.

Card Detection

Содержание MASS2










































































































































Результаты поиска

Содержание MASS2

Отзывы:

EZZE MASS2, Техническое руководство, Страница: 49 / 137

Результаты поиска

Содержание MASS2

Отзывы: