Extron electronics TLP 710MV Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 54

Extron electronics TLP 710MV Скачать руководство пользователя страница 47

Mounting

This section outlines the various options for:

•

Rack Mounting the TLP 710MV

•

Wall Mounting the TLP 710MV

•

Furniture Mounting the TLP 710MV

•

Wall Mounting the TLP 710MV with a Wallbox

•

Desktop Mounting the TLP 710TV

•

Removing the TLP 710TV base for VESA Mounting

•

VESA mounting the TLP 710TV

Rack Mounting the TLP 710MV

Underwriters Laboratories Guidelines for Rack Mounting

The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation

of these products in a rack:

Elevated operating ambient temperature —

If the unit is installed in a closed or

multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the equipment in an
environment compatible with the maximum ambient temperature (Tma: +122 °F, +45 °C)

specified by Extron.

Reduced air flow —

Install the equipment in the rack so that the equipment gets

adequate air flow for safe operation.

Mechanical loading —

Mount the equipment in the rack so that uneven mechanical

loading does not create a hazardous condition.

Circuit overloading —

Connect the equipment to the supply circuit and consider the

effect that circuit overloading might have on overcurrent protection and supply wiring.

Give appropriate consideration to the equipment nameplate ratings when addressing this

concern.

Reliable earthing (grounding) —

Maintain reliable grounding of rack-mounted

equipment. Pay particular attention to supply connections other than direct connections to
the branch circuit (such as the use of power strips).

Rack Mounting the TLP 710MV

The TLP 710MV can be mounted in any standard 19-inch equipment rack, using the
optional Extron RM 710M rack mounting kit (part number

70-970-01

). Follow the

instructions provided with the kit.

TLP 710MV and TLP 710TV • Mounting

41

«
...
45
46
47
48
49
...
»

Содержание TLP 710MV























































Отзывы:

Нет отзывов