Extron electronics IPCP 505, Руководство пользователя

Страница: 21 / 97

IPCP 505 • Hardware Features and Installation 13
Bidirectional Control and Communication Connections and Features
C
COM1 through COM6 RS-232 ports (-5 VDC to +5 VDC) (see figure 7 on
page 12) and
D
COM7 and COM8 RS-232/RS-422/RS-485 ports
(-5 VDC to +5 VDC) — Use
COM ports for serial control of a display or other device and to receive status messages
from the connected devices. These ports can send commands from a driver file.
IPCP 505 serial protocol:
• 300 to 115200 baud (9600 baud = default)
• 8 (default) or 7 data bits
• 1 (default) or 2 stop bits
• No parity (default), or even or odd parity
• Flow control support
•
COM1 - COM6: software-only
(XON, XOFF)
• COM7 and COM8:
hardware and software
Use the following diagram as a wiring guide to
cable the IPCP to other devices.
COM1
TX RX G G G
G
COM2
TX RX
TX RX G G TX RX
COM3
TX RX
G TX RX
COM7
COM4
CTS
COM5 COM6 COM8
TX RX
5A MAX
100 00-24 0V 50-6 0H 0Hz
RTS
G CTS TX RX RTS
SWITC HED 1 2V 2VDC
40W M AX T TO TAL
+ - + -
+ - + -
1 2
3 4
1 2 3 4 5 6 7 8
COM
TX
RX
TX
RX
RTS
CTS
D
OVER
LIMIT
O O
H H H H E E E D
C C C C C
L L
Projector, Panel
Display, PC, or Other
RS-232, RS-422, or
RS-485 Device
RS-232-
Controllable
Device
Receive (Rx)
Transmit (Tx)
Transmit
Receive Receive (Rx)
Transmit (Tx)
Ground
Request to send
Clear to send
Transmit
Rx Receive
Tx
CTS
RTS
G Ground
Rx
G
Tx
Strip wires
3/16" (5 mm) max.
NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends.
Rear Panel Front Panel
COM7, COM8
(RS-232, RS-422, RS-485)
COM1 - COM6
(RS-232)
Select protocol via software or
SIS command.
COM 1-8 port default protocol:
• 9600 baud
• 8 data bits • 1 stop bit
• no parity • no flow control
NOTE: The 5-pole COM ports support both
hardware and software flow control.
The 3-pole COM ports support software
flow control.
To COM1
- COM6
To COM7,
COM8
Heat Shrink
Heat Shrink
Over Shield Wires
RTS = Request to Send
CTS = Clear to Send
Tx = Transmitting Data
Rx = Receiving Data
Serial (COM) Ports
RS-232
Tx
Rx
Ground
RTS
CTS
RS-422
Tx-
Rx-
Ground
Tx+
Rx+
RS-485
Ground
COM7, COM8 Pin Configurations
Data-
(pins 1 & 2
tied together)
Data+
(pins 4 & 5
tied together)
Pin
1 (Tx)
2 (Rx)
3
(G)
4 (RTS)
5
(CTS)
Figure 9. Wiring for Serial Control
For bidirectional serial communication, the transmit, ground, and receive pins must be
wired at both the IPCP 505 and the other device. Each projector or other device may
require different wiring. For details, see the manual for that equipment or read the Extron
device driver communication sheet.
NOTE: Maximum distances between the IPCP and the device being controlled
may vary up to 200 feet (61 m). Factors such as cable gauge, baud rates,
environment, and output levels (from the IPCP and the device being controlled) all
affect transmission distance. Distances of about 50 feet (15 m) are typically not a
problem. In some cases the IPCP may be capable of transmitting and controlling
a given device via RS-232 up to 250 feet (76 m) away, but the RS-232 response
levels of that device may be too low for the IPCP to detect.
3/16"
(5 mm)
Max.
7/8"
(22 mm)
Heat Shrink
on Outer
Jacket to
Inner
Conductor
Transition
Extron
STP 20-2P Cable
TIP: STP 20-2P
cable, shown
at left, is
recommended
for these
connections.
For best
results,
insulate the
common or
drain wires
using heat
shrink.