Extron electronics FOX 500 Rx Скачать руководство пользователя страница 15

Страница: 15 / 40

FOX 500 Tx/Rx • Installation

Installation, cont’d

2-12

FOX 500 Tx/Rx • Installation

2-13

RS-232 Over Fiber port —

If you want the

FOX 500 to pass serial command signals to

the receiver, for serial control of a projector

for example, connect the host device to the

transmitter via three poles of this 5-pole captive

screw connector. See "Rear panel serial ports

connections" on page 2-14 to wire this connector.

If you connect only one fiber optic cable (item

below),

you will not receive reports from the controlled device. To

receive responses from the controlled device, you will need

to install two fiber optic cables.

The FOX 500 can pass RS-232 commands and responses

at rates up to 38400 baud.

Remote RS-232 port —

For serial control of the receiver,

connect a host device, such as a computer, touch panel control,

or RS-232 capable PDA, to the transmitter via three poles of this

5-pole captive screw connector.

See "Rear panel serial ports

connections" on page 2-14 to wire this connector.

See chapter 4, Remote Control, for definitions of the SIS

commands (serial commands to control the transmitter via this

connector).

Alarm outputs port

— For remote monitoring of

the status of fiber optic link 1, connect a locally-

constructed or furnished device to the receiver

via two poles of this 5-pole captive screw

connector. When the receiver does not detect a

light link on fiber cable Optical 1, pin 1 and pin 2 of this port

are shorted together.

Fiber optic connectors and LEDs

—

These units output continuous invisible light,

which may be harmful and dangerous to the eyes;

use with caution. For additional safety, plug the

attached dust caps into the optical transceivers

when the fiber optic cable is unplugged.

Ensure that you use the proper fiber cable for your

transmitter/receiver pair. Typically, singlemode fiber has a

yellow jacket and multimode cable has an orange jacket.

Only one fiber optic cable, Optical 1, is required for video,

audio, and serial command transmission. But, if you

connect only one fiber optic cable, you will not receive

RS-232 reports from the controlled device, and there will

be reduced front panel, Windows-based control program,

and RS-232 command functionality on the RX unit. To

receive responses from the controlled device and for full

functionality, you will need to install both fiber optic

cables.

Optical 1

— For all one-way video, audio, and

serial communications from the transmitter to

the receiver, connect a fiber optic cable to the

Optical 1 LC connector.

Connect the free end of this fiber optic cable

to the Optical 1 connector on the FOX 500 Tx

transmitter

(item

in "Transmitter rear panel

connections")

Optical 2

— For all one-way serial

communications from the receiver to the

transmitter, connect a fiber optic cable to the

Optical 2 LC connector.

Connect the free end of this fiber optic cable

to the Optical 2 connector on the FOX 500 Tx

transmitter

(item

in "Transmitter rear panel

connections")

Link 1 and Link 2 LEDs

— When lit, the link

is active (light is received).

AC power connector —

Plug a standard IEC power cord

into this connector to connect the receiver to a 100 VAC to

240 VAC, 50 or 60 Hz power source.

REMOTE

RS-232

ALARM

Tx Rx

1 2

OPTICAL

1 2*

OPTIONAL FOR

RETURN DATA

LINK

OPTICAL

2* 1

OPTIONAL FOR

RETURN DATA

LINK

RS-232

OVER FIBER

Tx Rx

REMOTE

RS-232

ALARM

Tx Rx

1 2

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201
Fax 07131 911203

[email protected]

Содержание FOX 500 Rx









































Результаты поиска

Содержание FOX 500 Rx

Отзывы:

Бренды по названию

Популярные бренды

Extron electronics FOX 500 Rx, Руководство пользователя

Результаты поиска

Содержание FOX 500 Rx

Отзывы:

Бренды по названию

Популярные бренды