background image

 

 

Please take a few moments to read this instruction manual before beginning 

assembly.  We have outlined a fast, clear and easy method to assemble this 

aircraft and familiarizing yourself with this process will aid in a quick, easy 

build. 

 

Please  read  the  following  paragraph  before  beginning 
assembly of your aircraft!  

 

THIS IS NOT A TOY!  Serious injury, destruction of property, or even death 
may result from the misuse of this product.  Extreme Flight RC is providing 
you,  the  consumer,  with  a  very  high  quality  model  aircraft  component  kit, 
from which you, the consumer, will assemble a flying model. It is beyond our 
control to monitor the finished aircraft you produce.  Extreme Flight RC will 
in  no  way  accept  or  assume  responsibility  or  liability  for  damages  resulting 
from the use of this user assembled product. This aircraft should be flown in 
accordance  with  the  AMA  safety  code.    It  is  highly  recommended  that  you 
join  the  Academy of  Model  Aeronautics  in  order  to  be  properly insured and 
operate  your  model  at  AMA  sanctioned  flying  fields  only.    If  you  are  not 
willing  to  accept  ALL liability  for  the use of  this  product,  please  return it to 
the place of purchase immediately.  

 

Extreme Flight RC, Ltd. guarantees this kit to be free of defects in materials 
and  workmanship  for  a  period  of  30  DAYS  from  the  date  of  purchase.    All 
warranty  claims  must  be  accompanied  by  the  original  dated  receipt.  This 
warranty  is  extended  to  the  original  purchaser  of  the  aircraft  kit  only.  
Extreme Flight RC in no way warranties its aircraft against flutter.  We have 
put these aircraft through the most grueling flight tests imaginable and have 
not  experienced  any  control  surface  flutter.    Proper  servo  selection  and 
linkage set-up is absolutely essential.  Inadequate servos or improper linkage 
set  up  may  result  in  flutter  and  possibly  the  complete  destruction  of  your 
aircraft.    If  you  are  not  experienced  in  this  type  of  linkage  set-up  or  have 
questions 

regarding 

servo 

choices, 

please 

contact 

us 

at 

[email protected] or 770-887-1794.  It is 

your

 responsibility to ensure 

the airworthiness of your model.  
 
 
 
 
 

Содержание Legacy Aviation Muscle Bipe






























Отзывы: