background image

3.

Pull the spring loaded idler back and slip the belt
over the top deck sheave. The belt should be routed
as shown in Figure 12.

g190065

Figure 12

View from Top of Blower

4.

Position the belt cover at an angle and slide it under
the mower frame (see Figure 13).

g038057

Figure 13

1.

Blower

3.

Mower frame

2.

Belt cover

5.

Push down on the back of the cover and slide it
backwards under the blower.

6.

With the belt cover resting on the deck, slide it
forward until it is seated under both lips on the deck.

g038066

Figure 14

1.

Blower

3.

Deck lip

2.

Belt cover

7.

Install the knob and its hardware.

Installing the Hopper Frame

1.

Remove the hairpin from the hopper frame. Insert
the hopper frame into the LH hopper mount bracket
(see Figure 15). Rest the other end of the hopper
frame between the tabs on the RH hopper mount
bracket. Reinstall the hairpin to secure the hopper
frame.

Note:

If the hopper frame does not seat properly in

the mount brackets, carefully use the hopper frame
to slightly adjust the alignment of the brackets. The
frame is designed to initially fit tight in the mounting
brackets. It may be necessary to use a mallet to
install.

7

 

Содержание ULTRAVAC 126-6122










Отзывы: