Exmark Turf Ranger FMD604 Скачать руководство пользователя | Manualshive

Страница: 41 / 48

background image

- 36 -

6. WASTE DISPOSAL

6.1 MOTOR OIL DISPOSAL

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil
at a certified recycling center or according to your state and local regulations.

6.2 BATTERY DISPOSAL

DANGER

POTENTIAL HAZARD

♦

Battery electrolyte contains sulfuric acid, which is

poisonous and can cause severe burns

WHAT CAN HAPPEN

♦

Swallowing electrolyte can be fatal or if it touches skin

can cause severe burns.

HOW TO AVOID THE HAZARD

♦

Wear safety glasses to shield eyes, and rubber gloves

to protect skin and clothing when handling electrolyte.

♦

Do not swallow electrolyte.

Federal law states that batteries should not be placed in the garbage. Management
and disposal practices must be within relevant federal, state, or local laws.

If a battery is being replaced or if the unit containing the battery is no longer operating
and is being scrapped, take the battery to a local certified recycling center. If no local
recycling is available return the battery to any certified battery reseller.

7. TROUBLE SHOOTING

7.1 MOWER TRACKS TO LEFT OR RIGHT.

a)

Check the drive tire pressures and tire circumferences. See 5.1.12.

b)

Turn knob on the right hydro control linkage in the direction that the mower needs
to be adjusted to. Turn the knob in 1/4 turn increments until the mower tracks
correctly.

7.2 MOWER CUTS UNEVENLY.

a)

Check the drive tire pressures and tire circumferences. See 5.1.12. A more
uniform cutting height may be obtained with higher tire pressure on rough terrain.
A lower tire pressure provides more flotation.

b)

Check deck support pins. Hairpin clips must be in the same hole position on each
support pin. See Section 5.2.1.

c)

Check deck support alignment and check mounting brackets to be sure all bolts
are tight.

d)

Check blades tip to tip for straightness. (They should be within 3/16”, or one
blade width from being in line.)

7.3 ENGINE WILL NOT START.

a)

Make sure battery has a full charge.

b)

Check that the throttle control is midway between “slow” and “fast” positions, and
choke is in “on” position for a cold engine or “off” position for a warm engine.

c)

Make sure the speed control lever is in the “true neutral” position. See Section 5.2.5.

d)

Check that the PTO is disengaged.

e)

Make sure the "OPC" levers are depressed.

f)

Check that there is fuel in the tank and that the fuel valve is open.

g)

Check that the spark plug wires are properly connected.

«
...
39
40
41
42
43
...
»

Содержание Turf Ranger FMD604

















































Отзывы:

Нет отзывов

Похожие инструкции для Turf Ranger FMD604

Бренд: Yard force Страницы: 53

Бренд: MTD Страницы: 20

Greensmaster 3150 04358

Бренд: Toro Страницы: 48

Бренд: Wolf Garten Страницы: 14

Eco Wheeler GM 413.2 R

Бренд: Garten Meister Страницы: 96

Бренд: Husqvarna Страницы: 3

Podadora 1302720

Бренд: Surtek Страницы: 8

Бренд: TIGA Страницы: 48

Бренд: Dolmar Страницы: 25

Бренд: GÜDE Страницы: 66

Бренд: GÜDE Страницы: 84

Бренд: GÜDE Страницы: 88

430/36-2 Li-ION

Бренд: GÜDE Страницы: 82

Бренд: GÜDE Страницы: 84

Бренд: Honda Страницы: 24

Бренд: Honda Страницы: 24

LAZER Z E Series

Бренд: Exmark Страницы: 76

Бренд: sunjoe Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды