Exmark Turf Ranger FMD604 Скачать руководство пользователя | Manualshive

Страница: 21 / 48

background image

- 16 -

STANDARD PISTOL GRIP HANDLES

ECS HANDLES

FIGURE 3

DRIVE LEVER, NEUTRAL LOCK LATCH OPERATION

4.1.4

PTO Engagement: Switch is located on left side of control console. The switch must
be

pulled out

to the ”

Rotate

” position to engage the blades. The switch is

pushed

in

to the “

Stop

” position to stop the blades. Operator must have operator presence

control levers depressed when PTO is engaged or engine will stop.

4.1.5

Choke Control: Located on the control console right hand side. Choke is used to
aid in starting a cold engine. The choke control is

pulled out

to be in the “

ON

”

position and

pushed in

to be in the “

OFF

” position.

DO NOT

run a warm engine

with choke in the “

ON

” position.

4.1.6

Throttle Control: Located on the control console’s right side. The throttle is used
to control engine speed. Moving the throttle control

forward

will increase engine

speed and moving it

to the rear

will decrease engine speed.

4.1.7

Speed Control Lever: Located in middle of control console, it controls the maximum
forward speed and is infinitely variable from neutral 0 mph to 6.75 mph.

Park brake must be disengaged to move speed control out of neutral or engine
will kill.

4.1.8

Ignition Switch: Located on the control console. The ignition switch is used to start
and stop the engine. The ignition switch has three positions, “Off”, “On” and
“Start”. Insert key into switch and rotate clockwise to the “On” position. Rotate
clockwise to the next position to engage the starter (key must be held against
spring pressure in this position). Operator must have

speed control lever in

neutral

,

OPC levers

depressed

and

PTO

disengaged

to start engine. When

engine starts, release key.

4.1.9

Hour Meter: Located on the left hand side of console just above the PTO switch.
The hour meter is connected to a pressure switch installed in the engine block
and it records the number of hours that the engine has run. If ignition switch is
left on without engine running, hour meter will not run.

NOTE: This switch is not a low oil sensor and will not alert the operator if the
engine oil is low.

4.1.10

Fuel Shut-Off Valve: Installed in the fuel line midway between the tank and
engine. The fuel shut-off valve is used to shut off the flow of fuel when parking
inside a building, during transportation to and from the job sites, and when the
machine will not be used for a few days.

Rotate valve 1/4 turn clockwise to shut fuel off. Rotate valve 1/4 turn counter-
clockwise to turn fuel on.

«
...
19
20
21
22
23
...
»

Содержание Turf Ranger FMD604

















































Отзывы:

Нет отзывов

Похожие инструкции для Turf Ranger FMD604

Бренд: Baroness Страницы: 19

Бренд: Baroness Страницы: 4

Бренд: Baroness Страницы: 5

Бренд: Baroness Страницы: 3

Бренд: Baroness Страницы: 142

Бренд: Baroness Страницы: 192

Бренд: Baroness Страницы: 60

Бренд: Daewoo Страницы: 37

Бренд: LAZER Страницы: 20

Бренд: Yard-Man Страницы: 11

Бренд: Yard-Man Страницы: 36

Бренд: Gardena Страницы: 13

Бренд: Yard-Man Страницы: 10

Бренд: Wizard Страницы: 48

Бренд: Aerotek Страницы: 18

Бренд: Toro Страницы: 48

Бренд: Racing Страницы: 20

Бренд: Cub Cadet Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды