Exmark Turf Ranger FMD604 Скачать руководство пользователя | Manualshive

Страница: 2 / 48

background image

WARNING

POTENTIAL HAZARD

♦

This product is a piece of power equipment.

WHAT CAN HAPPEN

♦

Failure to follow safe operating practices can result in serious

operator injury or even death.

HOW TO AVOID THE HAZARD

♦

Keep all shields, guards, and safety devices (especially the grass

discharge system) in place and in proper working condition.

♦

Stop engine and wait for all moving parts to stop. Remove spark

plug wire(s) or remove key before adjusting, servicing, or
performing maintenance.

♦

If mower deck becomes clogged, stop engine and wait for all

moving parts to stop. Remove spark plug wire(s) or remove key
before cleaning blockage.

♦

Keep hands, feet, and clothing away from power driven parts.

♦

Keep off mower unless seat platform is provided.

♦

Keep others off mower.

WARNING

POTENTIAL HAZARD

♦

Gasoline is harmful or fatal if swallowed. Long-term exposure to

vapors has caused cancer in laboratory animals.

WHAT CAN HAPPEN

♦

Failure to use caution may cause serious injury or illness.

HOW TO AVOID THE HAZARD

♦

Avoid prolonged breathing of vapors.

♦

Keep face away from nozzle and gas tank/container opening.

♦

Keep away from eyes and skin.

♦

Never siphon by mouth.

IMPORTANT

When the mower is used or operated on any California forest, brush or grass covered land, a working
spark arrester must be attached to the muffler. If not, the operator is violating state law, Section 4442
Public Resource Code. To acquire a spark arrester for your unit, see your Engine Service Dealer.

This spark ignition system complies with Canadian ICES-002
Ce système d’allumage par ètincelle de vèhicule est conforme à la norme NMB-002 du Canada

The enclosed Engine Owner’s Manual is supplied for information regarding The U.S.
Environmental Protection Agency (EPA) and the California Emission Control Regulation
of emission systems, maintenance and warranty.

Keep this engine Owner’s Manual with your unit. Should this engine Owner’s Manual
become damaged or illegible, replace immediately. Replacements may be ordered
through the engine manufacturer.

Exmark reserves the right to make changes or add improvements to its products at any time
without incurring any obligation to make such changes to products manufactured previously.
Exmark, or its distributors and dealers, accept no responsibility for variations

which may be

evident in the actual specifications of its products and the statements and descriptions
contained in this publication.

«
1
2
3
4
...
»

Содержание Turf Ranger FMD604

















































Отзывы:

Нет отзывов

Похожие инструкции для Turf Ranger FMD604

Бренд: Homelite Страницы: 22

Бренд: SANLI Страницы: 16

Бренд: Yard-Man Страницы: 12

Бренд: Snapper Страницы: 28

Бренд: Snapper Страницы: 24

Бренд: Ranger Страницы: 38

Бренд: Yardworks Страницы: 7

Бренд: LawnMaster Страницы: 32

Бренд: LawnMaster Страницы: 40

Бренд: LawnMaster Страницы: 40

Бренд: LawnMaster Страницы: 26

Бренд: Simplicity Страницы: 4

Бренд: Scag Power Equipment Страницы: 30

Бренд: Husqvarna Страницы: 5

Бренд: Husqvarna Страницы: 5

Бренд: Husqvarna Страницы: 5

Бренд: Husqvarna Страницы: 4

Бренд: Husqvarna Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды