Exmark Turf Ranger FMD604 Скачать руководство пользователя | Manualshive

Страница: 17 / 48

background image

- 12 -

3. ASSEMBLY INSTRUCTIONS

3.1 UNCRATE UNIT

3.1.1

Remove tractor and mower deck from crates.

3.2 SERVICE BATTERY:

The machine is shipped with a filled lead-acid battery.

3.2.1

Remove battery cover from machine.

DANGER

POTENTIAL HAZARD

♦

Charging the battery may produce explosive gasses

WHAT CAN HAPPEN

♦

Battery gasses can explode causing serious injury.

HOW TO AVOID THE HAZARD

♦

Keep sparks, flames, or cigarettes away from battery.

♦

Ventilate when charging or using battery in an

enclosed space.

♦

Make sure venting path of battery is always open once

battery is filled with acid.

3.2.2

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading
of the battery in the table below and charge the battery for the recommended time
interval to bring the charge up to a full charge of 12.6 volts or greater.

IMPORTANT:

Make sure the negative battery cables are disconnected and the

battery charger used for charging the battery has an output of 16 volts and 7
amps or less to avoid damaging the battery (see chart below for recommended
charger settings).

Voltage

Reading

Percent

Charge

Maximum

Charger Settings

Charging Interval

12.6 or greater

100%

16 volts/7 amps

No Charging Required

12.4 – 12.6

75 – 100%

16 volts/7 amps

30 Minutes

12.2 – 12.4

50 – 75%

16 volts/7 amps

1 Hour

12.0 – 12.2

25 – 50%

14.4 volts/4 amps

2 Hours

11.7 – 12.0

0 – 25%

14.4 volts/4 amps

3 Hours

11.7 or less

0%

14.4 volts/2 amps

6 Hours or More

CAUTION

POTENTIAL HAZARD

♦

If the ignition is in the “ON” position there is potential

for sparks and engagement of components.

WHAT CAN HAPPEN

♦

Sparks could cause an explosion or moving parts

could accidentally engage causing personal injury.

HOW TO AVOID THE HAZARD

♦

Be sure ignition switch is in the “OFF” position before

charging the battery.

3.2.3

Connect the negative battery cables.

WARNING:

Battery posts, terminals, and related accessories contain lead compounds,

chemicals known to the State of California to cause cancer and reproductive harm.

Wash

«
...
15
16
17
18
19
...
»

Содержание Turf Ranger FMD604

















































Отзывы:

Нет отзывов

Похожие инструкции для Turf Ranger FMD604

MT, MTL, MTEFI, MTLEFI

Бренд: Walker Страницы: 256

Бренд: Walker Страницы: 96

Бренд: Yard-Man Страницы: 40

Бренд: FERRI Страницы: 139

Бренд: LawnMaster Страницы: 28

Бренд: Poulan Pro Страницы: 52

Бренд: Supaswift Страницы: 12

Бренд: Qualcast Страницы: 15

Бренд: Weed Eater Страницы: 16

Бренд: Lastec Страницы: 68

Бренд: Yardworks Страницы: 35

Бренд: Hayter Страницы: 26

Бренд: Yazoo/Kees Страницы: 84

Бренд: Lawn-Boy Страницы: 28

DR Field and Brush Mower

Бренд: Country Home Products Страницы: 31

GF1800 ROPS Cab

Бренд: Kubota Страницы: 19

Бренд: Cub Cadet Страницы: 44

Бренд: Vicon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды