Exmark Lawn Tractor Скачать руководство пользователя | Manualshive

Страница: 43 / 52

background image

- 38 -

a) This adjustment must be made with the drive wheels turning. First raise the

frame and block up so that drive wheels can rotate freely.

b) Remove the electrical connection from the seat safety switch, located directly

to the left of the seat switch assembly beside the hydraulic oil reservoir.

Temporarily

install a jumper wire across the terminals in the connector of the

wiring harness.

c) Run the unit at least 5 minutes with the drive levers at full forward speed to

bring hydraulic system oil up to operating temperature.

d) Unhook seat latch and tilt seat forward.

e) Loosen lock nuts from the ball joints at each end of the LH pump control

linkage. (See Figure 17).

NOTE: The nut to the front of the unit on the LH rod has left-hand threads.

FIGURE 17

MOTION CONTROL ADJUSTMENT

f)

Start engine.

Brake must be engaged and motion control levers out to

start engine. Operator does not have to be in the seat because of the
jumper wire being used.

Run engine at full throttle and release brake.

g) The reverse indicator spring must be correct before the following

adjustments can be made. See Section 5.2.12.

NOTE: The motion control lever needs to be in neutral while making
any necessary adjustments.

The left rod assembly controls the left wheel and the right rod assembly
controls the right wheel.

h) Bring the LH motion control lever into the neutral position. Adjust LH pump

control rod length by rotating the double nuts on the rod in the appropriate
direction until the wheels slightly creep in reverse. (See Figure 17) Move
the motion control lever to the reverse position and while applying slight
pressure to the lever allow the reverse indicator spring to bring the levers
back to neutral. The wheel must stop turning or slightly creep in reverse.
When adjustment is complete, tighten lock nuts onto ball joints.

i)

Bring the RH motion control lever into the neutral position. Adjust the RH
pump control rod length by rotating the tracking adjustment knob in the
appropriate direction until the wheels slightly creep in reverse. Move the motion
control lever to the reverse position and while applying slight pressure to the
lever allow the reverse indicator spring to bring the levers back to neutral. The
wheel must stop turning or slightly creep in reverse. See Figure 17.

j)

Shut off unit. Remove jumper wire from wire harness connector and plug
connector into seat switch.

«
...
41
42
43
44
45
...
»

Содержание Lawn Tractor





















































Отзывы:

Нет отзывов

Похожие инструкции для Lawn Tractor

Бренд: EGO Страницы: 2

Бренд: Viking Страницы: 36

MOW'N MACHINE FZ22-2

Бренд: Woods Страницы: 48

Бренд: Etesia Страницы: 42

Бренд: Gardena Страницы: 11

Бренд: Snapper Страницы: 28

Бренд: MTD Страницы: 16

Бренд: P.Lindberg Страницы: 123

Бренд: Brinly Страницы: 28

Бренд: Webb Страницы: 24

Бренд: Cub Cadet Страницы: 40

Бренд: Bushranger Страницы: 14

Бренд: Kraftixx Страницы: 246

Бренд: Ikra Страницы: 56

Бренд: Ferris Страницы: 1

Бренд: Ferris Страницы: 40

Бренд: Ferris Страницы: 44

Бренд: Ferris Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды