Exmark Lawn Tractor Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

- 25 -

a) Stop engine, wait for all moving parts to stop, and remove key.

b) Clean all debris from rotating engine air intake screen and from around

engine shrouding.

c) Clean all debris from inside of pump drive belt compartment.

d) Inspect rubber engine baffles for proper fit. Replace if necessary.

5.1.4

Clean grass build-up under deck.

Service Interval: Daily

a)

Stop engine, wait for all moving parts to stop, and remove key.

b)

Raise deck to the transport (5” (12.7 cm) cutting height) position. Lift the
front of unit and support unit using jack stands or equivalent support.

CAUTION

POTENTIAL HAZARD

♦

Raising the mower deck for service or maintenance

relying solely on mechanical or hydraulic jacks could be
dangerous.

WHAT CAN HAPPEN

♦

The mechanical or hydraulic jacks may not be enough

support or may malfunction allowing the unit to fall, which
could cause injury.

HOW TO AVOID THE HAZARD

♦

DO NOT rely solely on mechanical or hydraulic jacks for

support. Use adequate jack stands or equivalent support.

c)

Clean out any grass build-up from underside of deck and in discharge chute.

5.1.5

Check mower blades.

Service Interval: Daily

a)

Stop engine, wait for all moving parts to stop, and remove key.

b)

Lift deck and secure in raised position as stated in Section 5.1.4.

c)

Inspect blades and sharpen or replace as required.

d)

Re-install the blades (if they were removed) in the following order (See
Figure 7):

1) Install bushing through blade with bushing flange on bottom (grass)

side of blade.

2) Install bushing/blade combo into spindle.

3) Install blade bolt and spring disc washer. Be sure the spring disc

washer cone is installed towards the bolt head. Place a block of wood
between front or rear baffles and the blade then torque the blade bolts
to 55-60 ft-lbs. (75-81 N-m).

«
...
28
29
30
31
32
...
»

Содержание Lawn Tractor





















































Отзывы:

Нет отзывов

Похожие инструкции для Lawn Tractor

Бренд: MTD Страницы: 4

Бренд: Ryobi Страницы: 48

Бренд: MK Martin Страницы: 30

Бренд: Yard force Страницы: 16

Бренд: Yard Machines Страницы: 72

Бренд: Yard-Man Страницы: 11

Бренд: Yazoo/Kees Страницы: 24

Бренд: Worx Страницы: 64

Smart Speed 569

Бренд: Troy-Bilt Страницы: 20

Бренд: Lawn-Boy Страницы: 28

Бренд: Kubota Страницы: 124

Бренд: Cub Cadet Страницы: 4

Бренд: Sears Страницы: 48

Self Propelled Mower

Бренд: Exmark Страницы: 16

Ultra Vac Laser Z

Бренд: Exmark Страницы: 24

Бренд: Exmark Страницы: 2

Бренд: Exmark Страницы: 52

LAZER Z DS-SERIES Operators

Бренд: Exmark Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды