Exmark Lawn Tractor Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 52

background image

- 39 -

5.2.14

Caster pivot bearings pre-load adjustment.

a) Remove dust cap from caster and tighten

nyloc nut until washers are flat and back
off 1/4 of a turn to properly set the pre-load
on the bearings. If disassembled, make
sure the spring washers are reinstalled as
shown in Figure 18.

5.2.15

Seat armrest adjustment.

a)

Lift armrest on seat. Locate square
tab marked with the numbers 1
through 4. Rotate square tab 1/4
turn to raise or lower the armrest in
approximately 1/4” (6.4 mm)
increments. See Figure 19.

6. WASTE DISPOSAL

6.1 MOTOR OIL DISPOSAL

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at
a certified recycling center or according to your state and local regulations.

6.2 BATTERY DISPOSAL

DANGER

POTENTIAL HAZARD

♦

Battery electrolyte contains sulfuric acid, which is

poisonous and can cause severe burns

WHAT CAN HAPPEN

♦

Swallowing electrolyte can be fatal or if it touches skin

can cause severe burns.

HOW TO AVOID THE HAZARD

♦

Wear safety glasses to shield eyes, and rubber gloves

to protect skin and clothing when handling electrolyte.

♦

Do not swallow electrolyte.

Federal law states that batteries should not be placed in the garbage. Management and
disposal practices must be within relevant federal, state, or local laws.

If a battery is being replaced or if the unit containing the battery is no longer operating and
is being scrapped, take the battery to a local certified recycling center. If no local
recycling is available return the battery to any certified battery reseller.

7. TROUBLE SHOOTING

7.1 MOWER PULLS LEFT OR RIGHT (W/LEVERS FULLY FORWARD).

a)

Refer to Tracking Adjustment Section 4.1.3.

b)

Check air pressure in tires; 13 psi/drive, 13 psi/pneumatic casters.

FIGURE 18

CASTER ADJUSTMENT

Armrest Adjustment
Tab Rotate ¼ Turn

FIGURE 19

ARMREST ADJUSTMENT

«
...
42
43
44
45
46
...
»

Содержание Lawn Tractor





















































Отзывы:

Нет отзывов

Похожие инструкции для Lawn Tractor

Бренд: H&S Страницы: 30

Бренд: Yard Machines Страницы: 72

Бренд: MTD Страницы: 16

Бренд: Nakayama Страницы: 14

Бренд: Wolf Garten Страницы: 46

Бренд: Scag Power Equipment Страницы: 38

Бренд: MTD Страницы: 12

Бренд: Snapper Страницы: 32

Broardmoor 2600, 1600, LT Series

Бренд: Simplicity Страницы: 2

Бренд: Yard-Man Страницы: 6

135 B TITAN DOD

Бренд: Stiga Страницы: 100

Бренд: SaMASZ Страницы: 37

Бренд: Dixon Страницы: 13

Бренд: Ferris Страницы: 48

Yanmar 59A40009727

Бренд: Cub Cadet Страницы: 24

Бренд: Fieldmaster Страницы: 25

Бренд: Kubota Страницы: 143

Бренд: Craftsman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды