Exmark Lawn Tractor Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 52

background image

- 19 -

To

turn right

while moving forward, move the

right lever

back toward neutral to

slow the right drive wheel.

To make a

zero turn

to the

left

, pull the left lever back beyond neutral while

holding the right lever slightly ahead of neutral.

To make a

zero turn

to the

right

, pull the right lever back beyond neutral while

holding the left lever slightly ahead of neutral.

Pulling

the

levers back

from the neutral position will cause the respective drive

wheels to rotate in a

reverse

direction (spring tension can be felt when moving

into reverse from neutral).

To turn to the left while backing, move the left lever forward toward neutral. To
turn to the right while backing, move the right lever forward toward neutral.

CAUTION

POTENTIAL HAZARD

♦

Machine can spin very rapidly by positioning one lever

too much ahead of the other.

WHAT CAN HAPPEN

♦

Operator may lose control of the machine, which may

cause damage to the machine or injury.

HOW TO AVOID THE HAZARD

♦

Use caution when making turns.

♦

Slow the machine down before making sharp turns.

4.1.3

Tracking Adjustment Knob: Located under the seat on the RH pump control
link. Rotating this knob allows fine tuning adjustments so that the machine
tracks straight with the drive levers in the full forward position.

Stop machine and wait for all moving parts to stop. Engage park brake. Unhook
seat latch and tilt seat forward to gain access to the tracking knob. Rotate the knob
clockwise (as viewed from the rear of the machine) to cause the machine to track
more to the right and counterclockwise to cause the machine to track more to the
left. Adjust in quarter-turn increments until the machine tracks straight. Check that
the machine does not creep when in neutral with the park brakes disengaged.

IMPORTANT: Do not rotate the knob too far, as this may cause the machine
to creep in neutral. Refer to section 5.2.13 for control linkage adjustment.

4.1.4

PTO Engagement Switch: Located just left of center on the console (left side of
ignition switch).

Switch must be

pulled out

to the “

ROTATE

” position to engage the blades.

Switch is pushed in to the “

STOP

” position to stop the blades.

4.1.5

Choke

Control: Located at lower center on the console (right side of ignition switch).

Choke is used to aid in starting a cold engine. The choke control is pulled out to
put the choke in the

“ON”

position and pushed in to put the choke control in the

“OFF”

position.

DO NOT

run a warm engine with choke in the “ON” position.

4.1.6

Throttle

Control: Located on console just right of center.

Throttle is used to control engine speed. Moving throttle lever

forward

will increase

engine speed and moving throttle lever

to the rear

will decrease engine speed.

4.1.7

Brake

Lever: Located on left side of unit, just to the front of the console. The

brake lever engages a parking brake on the drive wheels.

Pull

the lever up and

rearward

to

engage

the brake.

Push

the lever

forward

and

down

to

disengage

the brake.

The unit must be tied down and brake engaged when transporting.

«
...
22
23
24
25
26
...
»

Содержание Lawn Tractor





















































Отзывы:

Нет отзывов

Похожие инструкции для Lawn Tractor

Бренд: Yard Machines Страницы: 20

Бренд: Ferris Страницы: 60

2261ADC Articulator

Бренд: Lastec Страницы: 67

TECHline NEXTTECH L X4

Бренд: ZCS Страницы: 42

Бренд: Rotomec Страницы: 40

EcoCut 135 Z-042

Бренд: Talex Страницы: 164

Бренд: Meec tools Страницы: 38

Бренд: Bushranger Страницы: 20

Бренд: Bushranger Страницы: 24

Бренд: Gardeo Страницы: 53

Бренд: Gardenline Страницы: 28

Бренд: GARDEO PRO Страницы: 99

Бренд: Gardena Страницы: 12

Бренд: Ferris Страницы: 1

Бренд: Ferris Страницы: 40

Бренд: Ferris Страницы: 44

Бренд: Ferris Страницы: 48

Бренд: Ferris Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды