The Visual Deterrent LED flashes whenever the system is armed to deter a break-in, and
is also a visual indicator of what state the security part of the system is in at any given time.
It is located on the top of the Information and Programming Module. These are the conditions
that are reflected by the Visual Deterrent LED:
1) Off
= The security system is disarmed and not performing any automatic
functions.
2) On Constant
= The security system is in the Valet Mode.
3) Flashing Slow
= The security system is Fully Armed.
4) Flashing Fast
= The 3 second Arming Delay, the 30 second Last Door Arming
feature or 90 second Automatic Rearming feature is in progress.
Automatic Transmitter Verification
TM
: After the ignition is turned "on", the Visual
Deterrent LED will flash to indicate the number of transmitters programmed to operate your
system. For example, two flashes between pauses indicates that only two transmitters are
coded to operate your system. This feature, in normal operation, shows how many operable
transmitters there are for 10 seconds every time the ignition switch is turned "on".
5) Flash-1x & Pause = 1 transmitter code is stored in the system's memory.
6) Flash-2x & Pause = 2 transmitter codes are stored in the system's memory.
7) Flash-3x & Pause = 3 transmitter codes are stored in the system's memory.
8) Flash-4x & Pause = 4 transmitter codes are stored in the system's memory.
This feature also warns of unauthorized transmitter programming; please see Page 6.
Visual Deterrent LED
Page - 25
Zone Violation: If the system is activated the Red Visual Deterrent LED will start to flash
and pause the #9 through #12 sequences to indicate which protected circuit caused the
activation. This is seen while the system is activated and after disarming, until the ignition
switch is turned "on", which will clear the security system's memory. The system's memory
circuit can store four different codes, and if multiple violations involving different zones
occurred, the different zones will be shown.
9) Flash-1x & Pause
= System was activated from current sensing.
10) Flash-2x & Pause
= System was activated from the hood or trunk circuit wire.
11) Flash-3x & Pause
= System was activated from the door circuit wire.
12) Flash-4x & Pause
= System was activated from the auxiliary input.
13) Flash-5x & Pause
= System's prewarn feature was activated.
Zone Testing: Every time the ignition key is turned off , the Visual Deterrent LED will flash
and pause the #14 through #18 sequences to indicate if a protected circuit, or "zone", is in
an activated state. For example: open a door after the ignition is turned off and the Red Visual
Deterrent LED will start flashing 3 times and pause until the door is closed. If another
protected entry point is violated while the door is still open, then the Red Visual Deterrent
LED will alternate flashing both zone violation codes.
14) Flash-1x & Pause
= System is detecting a trigger from a current spike.
15) Flash-2x & Pause
= System is detecting a trigger from the hood or trunk circuit.
16) Flash-3x & Pause
= System is detecting a trigger from the door circuit wire.
17) Flash-4x & Pause
= System is detecting a trigger from the auxiliary input.
18) Flash-5x & Pause
= System is detecting a trigger from the prewarn input.
Page - 26
Page - 27
The Digital Status Indicator is found on Information and Programming Module and
provides more direct system status information the user. This information is displayed in the
form of letters, numbers and symbols. Unlike the Visual Deterrent LED, these displays last,
for most applications, for a shorter period of time. Please note that the Digital Status Indicator
does has no display when driving after display periods, or after timing out upon arming the
system.
1) Display shows
for 30 seconds after the ignition has been turned "off" indicates that
the system is in the Valet Mode.
2) Display shows
for 10 seconds after the following display indicates that the security
system is Fully Armed.
3) Display shows
indicates that the 3 second Arming Delay, the 30 second Last Door
Arming feature or 90 second Automatic Rearming feature is in progress.
4) Display shows
indicates that the system is in one of the programming modes.
5) Display shows
to
for 10 or 90 seconds after the ignition is turned "on" indicates
the number of transmitters capable of operating the system.
6) Display shows
indicates that the system is detecting a current spike in the vehicle's
Digital Status Indicator
Page - 28
electrical system as part of the Zone Testing feature explained in the previous section.
7) Display shows
indicates that the system is detecting an open hood or trunk as part
of the Zone Testing feature explained in the previous section.
8) Display shows
indicates that the system is detecting an open door as part of the
Zone Testing feature explained in the previous section.
9) Display shows
indicates that the auxiliary port sensor is in a triggered state as part
of the Zone Testing feature explained in the previous section.
10) Display shows
indicates that the Prewarn feature is in a triggered state as part of the
Zone Testing feature explained in the previous section.
11) Display shows a numeral followed by
upon disarming indicates that the system
was triggered by a current spike. The numeral signifies the history of events.
12) Display shows a numeral followed by
upon disarming indicates that the system
was triggered by the hood or trunk circuit. The numeral signifies the history of events.
13) Display shows a numeral followed by
upon disarming indicates that the system
was triggered by the door circuit. The numeral signifies the history of events.
