Silent Arming and Disarming: Upon arming or disarming, if the confirmation siren chirps
are not desired, simply press and release the transmitter's small center button before pressing
and releasing the large button.
Sensor Bypass: Your Excalibur Gold system provides you with the convenient option of
temporarily deactivating the Auxiliary Sensor without affecting any other trigger circuit. To
deactivate the Auxiliary Sensor, simply press and release the small lower transmitter button
within 3 seconds after pressing the large transmitter button when arming the system. You will
hear a second siren chirp, confirming the security system has armed without the sensor circuit
protecting the vehicle. The next time you arm the security system, the system will reset to its
normal condition, and the Auxiliary Sensor will again be part of your protection. If desired,
a second Auxiliary Sensor may be easily added to your system.
Page - 13
Automatic Last Door Arming: Your security system can be programmed to arm automati-
cally when the vehicle's last door is closed. The moment the last door closes the siren will chirp
once, the parking lights and dome lights will flash once and the Visual Deterrent LED will begin
to flash rapidly. Thirty seconds later the siren will chirp again, the lights will flash once, the
doors will lock (if the Last Door Lock feature has also been chosen) and 3 seconds later the
Visual Deterrent LED will slow to a steady flash, confirming that the security system is fully
armed. During this 30 second period, the Digital Status Indicator
Automatic System Arming & Rearming
Page - 14
will show " ", and then change to " " for ten seconds when fully armed. However, if a point
of entry is reopened before the single siren chirp and light flash at 30 seconds, this passive
arming process stops, and will reset to start over again when that point of entry is reclosed.
"Automatic Last Door Arming" offers a high level of security, since it does not require
you to remember to arm the security system when you leave your vehicle. Additionally,
Automatic Last Door Arming may entitle you to an insurance discount. Please note that the
previously described Arming Bypass feature does not operate with Automatic Last Door
Arming. The Arming Bypass is designed to operate only when arming from the transmitter,
because all protected entries must be closed prior to the Automatic Last Door Arming
sequence to start.
To prevent the system from automatically arming while the vehicle is being refueled you
should put the system in Valet Mode, keep your door open. We do not recommend leaving
your ignition key turned "on". Last Door Arming does not effect the operation or use of the
transmitter to arm the system - if desired, the transmitter may still be used to arm the system
at any time.
Automatic Rearming:
Selecting this feature adds Automatic Rearming, which is
independent of Automatic Last Door Arming. This feature will cause the system to
automatically rearm itself 90 seconds after disarming, unless the ignition switch is turned
"on". This prevents the accidental disarming of the system by the inadvertent pressing of
the transmitter's button while placing it in a purse or pocket. If the "Automatic Relocking"
Programmable Feature is utilized, the doors will also lock when the system automatically
rearms. Automatic Rearming is indicated by a fast flashing Visual Deterrent LED during the
90 seconds, then a parking and dome light flash when the system rearms.
Remote Valet: This Feature, which only operates as part of the Automatic Rearming
Feature, will temporarily cancel the Automatic Rearming. To use Remote Valet, press and
release the large transmitter button to disarm the system; then, within 3 seconds, press and
release the small lower transmitter button. The parking lights will flash on and off, and the
LED Status Indicator will illuminate steady to confirm Remote Valet operation. The Digital
Status Indicator will show " " for 30 seconds The system will remain in Remote Valet mode
until armed again by the transmitter; or, the Valet Switch may be pressed to place the system
in the "standby" mode.
Page - 15
While the security system is armed, the Visual Deterrent LED will be flashing. Should any
intrusion attempt occur, your system will instantly activate, or "trigger". When triggered, the
system will:
1)
Sound the electronic siren or the vehicle's horn. The siren features six different
tones, and every 5 seconds the siren will change the tone to generate more attention
to the vehicle. If used instead of the siren, the horn will sound a series of honks,
sounding for one second, then pausing one second. Every ten seconds, the horn
will pause honking completely for 5 seconds, which avoids overheating the horn.
This will occur for the duration of the activated cycle.
Security System Armed & Activated
Page - 16
2)
The exterior lights will flash.
3)
The doors will relock so that the thief cannot easily regain entry. This feature is so
unique that the security system monitors the status of the door and, if open, the
system waits until the door is closed, at which time it relocks the doors.
The siren and the parking lights will stay active for 60 seconds unless you disarm the
system with the transmitter or by using the Valet Override. If all protected entries are secure
at the end of 60 seconds, the system will stop and rearm automatically to detect another entry
attempt. If there is a protected entry still open, or an optional sensor still in a triggered state
at the end of 60 seconds, the system will reactivate for two more 60 second cycles.
The system will stop after a total of 3 minutes and rearm automatically, while ignoring only
the open entry or triggered circuit. When the entry is closed, protection will begin instantly
for that circuit.
After the security system has been activated, the disarm confirmation will no longer be
2 siren chirps, and the parking and interior lights staying on. Instead, the system will respond
by producing 4 siren chirps and the parking lights and interior lights will flash 4 times before
staying on for 30 seconds. The Digital Status Indicator will first flash a number, then letter,
which indicates the protected zone which was violated and number of violations. If more than
one zone was violated, all be flashed in sequence. The Visual Deterrent LED will also change
to flashing two to five times, then pausing 1 second to indicate which protected zone
