EWM Taurus 335 Synergic S TKM Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 103

background image

Design and function

Shielding gas supply

099-005215-EW501

29.06.2011

85

5.10

Shielding gas supply

5.10.1

Connecting the shielding gas supply

WARNING

Incorrect handling of shielding gas cylinders!
Incorrect handling of shielding gas cylinders can result in serious and even fatal injury.
• Observe the instructions from the gas manufacturer and in any relevant regulations

concerning the use of compressed air!

• Place shielding gas cylinders in the holders provided for them and secure with fixing

devices.

• Avoid heating the shielding gas cylinder!

CAUTION

Faults in the shielding gas supply.
An unhindered shielding gas supply from the shielding gas cylinder to the welding
torch is a fundamental requirement for optimum welding results. In addition, a blocked
shielding gas supply may result in the welding torch being destroyed.
• Always re-fit the yellow protective cap when not using the shielding gas connection.
• All shielding gas connections must be gas tight.

NOTE

Before connecting the pressure regulator to the gas cylinder, open the cylinder valve
briefly to expel any dirt.

«
...
83
84
85
86
87
...
»

Содержание Taurus 335 Synergic S TKM








































































































Отзывы:

Нет отзывов

Похожие инструкции для Taurus 335 Synergic S TKM

Бренд: hager Страницы: 3

Бренд: Lamp Страницы: 2

Бренд: Lamp Страницы: 8

Бренд: M-Audio Страницы: 12

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: X10 Страницы: 4

Бренд: salmson Страницы: 16

Бренд: bester Страницы: 68

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: ShoreStation Страницы: 15

ZS 80 KST Extreme Series

Бренд: steute Страницы: 20

Бренд: Bose Sicilia Страницы: 24

Бренд: 2N Telekomunikace Страницы: 12

Бренд: Innovative Technology Страницы: 14

7.4VOLT HEATED GLOVES

Бренд: Mobile Warming Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды