EWM Taurus 335 Synergic S TKM Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 103

background image

Design and function

MIG/MAG welding

099-005215-EW501

29.06.2011

61

5.7.18

Remote control

CAUTION

Damage to the machine due to improper connection!
The remote controls have been developed to be connected to welding machines or wire
feed units only. Connecting them to other machines may cause damage to the
machines!
• Observe the operating instructions for the welding machine or wire feed unit!
• Switch off the welding machine before connecting!

The operation of the remote control and its settings are directly dependent on the configuration of the
respective welding machine or wire feed unit. The settings are defined by changeover switches or by
setting special parameters (dependent on the control).

• Infinitely adjust wire feed speed and arc length correction (welding voltage) (the function is only

available in program 0). Switch the “welding torch function” changeover switch to the program position.

Special functions
• Adjust wire feed speed and arc length correction within defined limits.

The function can only be enabled in connection with an M3.7x machine control.
Special parameter P7 must be switched on (see corresponding documentation).
The function can be used in all programs except program 0.

«
...
59
60
61
62
63
...
»

Содержание Taurus 335 Synergic S TKM








































































































Отзывы:

Нет отзывов

Похожие инструкции для Taurus 335 Synergic S TKM

Бренд: U-Line Страницы: 7

Бренд: Ace Страницы: 13

Бренд: Omni Страницы: 108

Бренд: Q-See Страницы: 9

KegMaster 4 Series

Бренд: Keg King Страницы: 17

Бренд: Fender Страницы: 14

Millermatic 212

Бренд: Miller Electric Страницы: 44

HOME THEATER SPEAKERS

Бренд: Sonance Страницы: 8

Бренд: JAMO Страницы: 72

DRINKWORKS Home Bar Classic

Бренд: Keurig Страницы: 32

D2 C2X05DC024 Series

Бренд: E2S Страницы: 9

Бренд: iTrak Страницы: 6

Бренд: Manitou Systems Страницы: 244

Бренд: Ferguson Страницы: 13

MR Confon Starter f MKII+

Бренд: Cambridge Research Systems Страницы: 34

Бренд: JLG Страницы: 48

Бренд: U-Prox Страницы: 3

Бренд: Chamberlain Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды