EWM Taurus 335 Synergic S TKM Скачать руководство пользователя страница 78

Страница: 78 / 103

Design and function

TIG welding

099-005215-EW501

29.06.2011

Non-latched mode

Figure 5-41

Selection

• Select non-latched operating mode

Step 1
• Press and hold torch trigger.

• Shielding gas is expelled (gas pre-flows).

The arc is ignited using liftarc.
• Welding current flows with pre-selected setting.

Step 2
• Release torch trigger.

• Arc is extinguished.

• Gas post-flow time elapses.

Special, non-latched

END

START

Figure 5-42

Selection

• Select non-latched special mode

Step 1
• Press and hold torch trigger

• Shielding gas is expelled (gas pre-flows)

The arc is ignited using liftarc.
• Welding gas flows with pre-selected setting in start program “P

START

”.

• After the “tstart” ignition current time elapses, the welding current rises with the set upslope time “tS1”

to the main program “P

”.

Step 2
• Release torch trigger.

• The welding current reduces with the downslope time “tSe” to the end program “P

END

”.

• After the end current time “end” elapses, the arc will extinguish.

• Gas post-flow time elapses.

Содержание Taurus 335 Synergic S TKM








































































































Результаты поиска

Содержание Taurus 335 Synergic S TKM

Отзывы:

Похожие инструкции для Taurus 335 Synergic S TKM

Бренды по названию

Популярные бренды

EWM Taurus 335 Synergic S TKM, Руководство по эксплуатации

Результаты поиска

Содержание Taurus 335 Synergic S TKM

Отзывы:

Похожие инструкции для Taurus 335 Synergic S TKM

Бренды по названию

Популярные бренды