EWM Taurus 335 Synergic S TKM Скачать руководство пользователя страница 4

Страница: 4 / 103

Contents

Notes on the use of these operating instructions

099-005215-EW501

29.06.2011

5.7.8

MIG/MAG operating point .............................................................................................39

5.7.8.1

Selecting the display unit...............................................................................39

5.7.8.2

Operating point setting using material thickness ..........................................39

5.7.8.3

Arc length correction setting..........................................................................39

5.7.8.4

Accessory components for operating point setting .......................................40

5.7.9

MIG/MAG welding data display ....................................................................................40

5.7.10

forceArc.........................................................................................................................41

5.7.11

rootArc ..........................................................................................................................41

5.7.12

MIG/MAG functional sequences / operating modes.....................................................42

5.7.12.1

Explanation of signs and functions................................................................42

5.7.13

MIG/MAG program sequence ("Program steps" mode) ...............................................52

5.7.13.1

Selection of the program sequence parameter .............................................52

5.7.13.2

MIG/MAG

overview of parameters ................................................................53

5.7.13.3

Example, tack welding (non-latched) ............................................................54

5.7.13.4

Example, aluminium tack welding (non-latched special) ..............................54

5.7.13.5

Example, aluminium welding (latched special) .............................................55

5.7.13.6

Example, visible seams (latched super pulse) ..............................................56

5.7.14

Main program A mode ..................................................................................................57

5.7.14.1

Selecting parameters (program A) ................................................................59

5.7.15

MIG/MAG automatic cut-out .........................................................................................59

5.7.16

Standard MIG/MAG torch .............................................................................................60

5.7.17

MIG/MAG special-torches.............................................................................................60

5.7.17.1

Program- and Up- / down operation..............................................................60

5.7.18

Remote control .............................................................................................................61

5.7.19

Advanced settings ........................................................................................................62

5.7.19.1

Selecting, changing and saving parameters .................................................62

5.7.19.2

Reset to factory settings................................................................................64

5.7.19.3

The special parameters in detail ...................................................................65

5.7.19.4

Switching between Push/Pull and intermediate drive ...................................73

5.8

TIG welding ..................................................................................................................................74

5.8.1

Welding torch and workpiece line connection ..............................................................74

5.8.2

Welding task selection ..................................................................................................76

5.8.3

Welding current setting .................................................................................................76

5.8.4

TIG arc ignition .............................................................................................................76

5.8.4.1

Liftarc ignition ................................................................................................76

5.8.5

Function sequences/operating modes..........................................................................77

5.8.5.1

Explanation of signs and functions................................................................77

5.8.6

TIG automatic cut-out ...................................................................................................80

5.8.7

TIG program sequence ("Program steps" mode) .........................................................81

5.8.7.1

TIG parameter overview................................................................................81

5.9

MMA welding................................................................................................................................81

5.9.1

Connecting the electrode holder and workpiece lead ..................................................82

5.9.2

Welding task selection ..................................................................................................83

5.9.3

Welding current setting .................................................................................................83

5.9.4

Arcforce.........................................................................................................................83

5.9.5

Hotstart .........................................................................................................................84

5.9.6

Antistick.........................................................................................................................84

5.9.7

Parameter overview......................................................................................................84

5.10

Shielding gas supply ....................................................................................................................85

5.10.1

Connecting the shielding gas supply ............................................................................85

5.10.2

Gas test ........................................................................................................................86

5.10.3

“Rinse tube package” function ......................................................................................86

5.10.4

Setting the shielding gas quantity.................................................................................87

Содержание Taurus 335 Synergic S TKM








































































































Результаты поиска

Содержание Taurus 335 Synergic S TKM

Отзывы:

Похожие инструкции для Taurus 335 Synergic S TKM

Бренды по названию

Популярные бренды

EWM Taurus 335 Synergic S TKM, Руководство по эксплуатации

Результаты поиска

Содержание Taurus 335 Synergic S TKM

Отзывы:

Похожие инструкции для Taurus 335 Synergic S TKM

Бренды по названию

Популярные бренды