EWM Picomig 180 puls TGE Скачать руководство пользователя страница 57

Страница: 57 / 65

Rectifying faults

Error messages (power source)

099-005545-EW501

17.12.2020

7.2 Error messages (power source)

A welding machine error is indicated by the collective fault signal lamp (A1) lighting up and an

error code (see table) being displayed in the machine control display. In the event of a machine

error, the power unit shuts down.

• If multiple errors occur, these are displayed in succession.
• Document machine errors and inform service staff as necessary.

Error message Possible cause

Remedy

E 0

Start signal set in the event of er-

rors

Do not press the torch trigger or the foot-opera-

ted remote control

E 4

Temperature error

Allow the machine to cool down

E 5

Mains overvoltage

Switch off the machine and check the mains vol-

tage

E 6

Mains undervoltage

E 7

Electronics error

Switch the machine off and on again.

If the error persists, notify service department

E 9

Secondary overvoltage

E12

Voltage reduction error (VRD)

E13

Electronics error

E14

Adjustment error in current record-

ing

Switch off the machine, place the electrode hol-

der in an insulated position and switch the ma-

chine back on. If the error persists, notify service

department

E15

Error in one of the electronics

supply voltages

Switch the machine off and on again.

If the error persists, notify service department

E23

Temperature error

Allow the machine to cool down

E32

Electronics error

Switch the machine off and on again.

If the error persists, notify service department

E33

Adjustment error in voltage record-

ing

Switch off the machine, place the electrode hol-

der in an insulated position and switch the ma-

chine back on. If the error persists, notify service

department

E34

Electronics error

Switch the machine off and on again.

If the error persists, notify service department

E37

Temperature error

Allow the machine to cool down

E40

Motor fault

Check wire feed mechanism,

switch the machine off and on again, inform the

service department if the fault persists.

E51

Earth fault (PE error)

Connection between welding wire and machine

casing

E55

Failure of a mains phase

Switch off the machine and check the mains vol-

tage

E58

Short circuit in welding circuit

Switch off the machine and check welding current

leads for correct installation, e.g. by placing the

electrode holder in an insulated position; detach

current lead from degaussing.

Содержание Picomig 180 puls TGE


































































Результаты поиска

Содержание Picomig 180 puls TGE

Отзывы:

Похожие инструкции для Picomig 180 puls TGE

Бренды по названию

Популярные бренды

EWM Picomig 180 puls TGE, Руководство по эксплуатации

Результаты поиска

Содержание Picomig 180 puls TGE

Отзывы:

Похожие инструкции для Picomig 180 puls TGE

Бренды по названию

Популярные бренды