EWM Picomig 180 puls TGE Скачать руководство пользователя

Страница: 30 / 65

Design and function

MIG/MAG welding

099-005545-EW501

17.12.2020

5.2.2 Wire feed

CAUTION

Risk of injury due to moving parts!

The wire feeders are equipped with moving parts, which can trap hands, hair, clothing

or tools and thus injure persons!

• Do not reach into rotating or moving parts or drive components!

• Keep casing covers or protective caps closed during operation!

Risk of injury due to welding wire escaping in an unpredictable manner!

Welding wire can be conveyed at very high speeds and, if conveyed incorrectly, may es-

cape in an uncontrolled manner and injure persons!

• Before mains connection, set up the complete wire guide system from the wire spool to the

welding torch!

• Check wire guide at regular intervals!

• Keep all casing covers or protective caps closed during operation!

5.2.2.1 Inserting the wire spool

CAUTION

Risk of injury due to incorrectly secured wire spool.

If the wire spool is not secured properly, it may come loose from the wire spool support

and fall to the ground, causing damage to the machine and injuries.

• Make sure to correctly fasten the wire spool to the wire spool support.

• Before you start working, always check the wire spool is securely fastened.

Figure 5-9

Item Symbol Description

Carrier pin

For fixing the wire spool

Knurled nut

For fixing the wire spool

Содержание Picomig 180 puls TGE


































































Результаты поиска

Содержание Picomig 180 puls TGE

Отзывы:

Похожие инструкции для Picomig 180 puls TGE

Бренды по названию

Популярные бренды

EWM Picomig 180 puls TGE, Руководство по эксплуатации

Результаты поиска

Содержание Picomig 180 puls TGE

Отзывы:

Похожие инструкции для Picomig 180 puls TGE

Бренды по названию

Популярные бренды