EVS Synapse U4T100 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 68

background image

INSTALLATION AND CONFIGURATION MANUAL

U4T100-U4T140

8

3 A Quick Start

When powering-

up

On powering up the Synapse frame, the card set will use basic data
and default initialisation settings. All LED’s will light during this
process. After initialisation, several LED’s will remain lit – the
exact number and configuration is dependent upon the number of
inputs connected and the status of the inputs.

Changing settings

and parameters

The front panel controls or the Synapse Cortex can be used to
change settings. An overview of the settings can be found in chapter
5, 6 and 7 of this manual.

Front Panel

Control

Front Panel Display and Cursor

Settings are displayed and changed as follows;

Use the cursor ‘arrows’ on the front panel to select the menu and
parameter to be displayed and/or changed.

Press ►

To go forward through the menu structure.

Press ◄

To go back through the menu structure.

Press ▲

To move up within a menu or increase the value of
a parameter.

Press ▼

To move down through a menu or decrease the
value of a parameter.

Note

Whilst editing a setting, pressing ► twice will
reset the value to its default

[No Alarms]

«
...
8
9
10
11
12
...
»

Содержание Synapse U4T100





































































Отзывы:

Нет отзывов

Похожие инструкции для Synapse U4T100

Бренд: Bang & Olufsen Страницы: 6

BeoSound 5 Encore

Бренд: Bang & Olufsen Страницы: 25

Бренд: Bang & Olufsen Страницы: 28

Бренд: ItsImagical Страницы: 34

Interlogix RF440I4

Бренд: United Technologies Страницы: 4

Бренд: Lynx Страницы: 14

Бренд: Burg Wächter Страницы: 21

Бренд: Optex Страницы: 2

Бренд: Jensen Страницы: 2

Virtuoso Series

Бренд: Vitek Страницы: 20

Trailblazer 251

Бренд: Miller Страницы: 48

Бренд: F&F Страницы: 8

Elko AirSF-100L

Бренд: iNels Страницы: 3

Бренд: Lincoln Electric Страницы: 46

Бренд: Eaton Страницы: 63

Бренд: First Alert Страницы: 56

Бренд: Saferhomee Страницы: 14

Prestige Close Coupled Systems

Бренд: Rinnai Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды