EVS Synapse U4T100 Скачать руководство пользователя страница 45

Страница: 45 / 68

EVS Broadcast Equipment SA

AddOnFrmtIn01/02

AddOnFrmtIn31/32

These status items indicate the detected audio format of each audio
pair from the quad speed addon bus. Can be one of the following
formats:

▪

N/A

▪

PCM

▪

Null

▪

AC-3

▪

TimeStmp

▪

MPEG-1

▪

MPEG-2

▪

SMPTE-KLV

▪

Dolby E

▪

Caption data

▪

UserDef

▪

Rsvd

▪

Enh Ac-3

SOF-E_A1/2A

Displays the start line of a Dolby E frame. Can be a value between 0
and 1124 (dependant on input and output format).

NET STATUS

IP_Addr0

This item displays the status of the IP address. It can be manual,
DHCP asking, DHCP Leased or DHCP Infin.

MAC0

This item displays the MAC address of the card.

IP0

This item displays the current IP address of the card.

NM0

This item displays the current Netmask of the card.

GW0

This item displays the current Standard Gateway of the card.

Содержание Synapse U4T100





































































Результаты поиска

Содержание Synapse U4T100

Отзывы:

Похожие инструкции для Synapse U4T100

Бренды по названию

Популярные бренды

EVS Synapse U4T100, Руководство по установке и настройке

Результаты поиска

Содержание Synapse U4T100

Отзывы:

Похожие инструкции для Synapse U4T100

Бренды по названию

Популярные бренды